824BP2/5-4 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > 824BP2/5-4

Preview

824BP2/5-4: Description8 Bit Programmable 2-Pole Pair Filters; File Size442KB，7 Pages; ManufacturerETC1

Download Datasheet View All

824BP2/5-4 Overview

8 Bit Programmable 2-Pole Pair Filters

Preview

Download Datasheet

View All

824BP Series

Band Pass

Description:

The 824BP Series is a 2-pole-pair digitally

programmable precision band-pass active filter that

provides high performance in a compact 2" x 2"

footprint. These new filters take advantage of the

company’s proprietary designs using surface-mount

technology to provide a low profile, compact package

in minimal board space. 824BP filters are factory

tuned to one of three factory set tuning ranges or 8-

bit custom ranges from 1 Hz to 25.6 kHz. Each filter

type features a near theoretical amplitude/phase

response along with low output voltage noise

enabling these filters to achieve a 10,000:1 or better

dynamic signal range.

Pretuned to within ±2% of the center frequency,

band-pass 824BP filters pass all frequencies lying

between the upper and lower -3dB points of the

amplitude response curve. Available Q’s for 824BP

models are 1, 2, 5, or 10.

Features/Benefits:

• Compact 2.0"L x 2.0"W footprint minimizes board

space requirements.

• Plug-in ready-to-use, reducing engineering design

and manufacturing cycle time.

• Factory tuned, no external clocks or adjustments

needed.

• Broad range of center frequencies to meet a wide

range of applications.

Applications

• Power line interference rejection

• Transducer output filtering

• Production test instrumentation

• Medical electronics equipment and research

• Comb filtering and equalization

• Noise and harmonic analysis

• RMS measurements

• Frequency spectrum analysis

8 Bit Programmable

2-Pole Pair Filters

Programmable Specifications:

. . . . . . . . . . . .Page

Digital Tuning & Control . . . . . . . . . . . . . . . . . . . . .2

Available Band-Pass Models:

824BP2

2 pole pair . . . . . . . . . . . . . . . . . . .3

General Specifications:

Ordering Information . . . . . . . . . . . . . . . . . . . . . . .4

Pin-Out/package data . . . . . . . . . . . . . . . . . . . . . .4

25 Locust St, Haverhill, Massachusetts 01830 • Tel: 800/252-7074, 978/374-0761 • FAX: 978/521-1839

e-mail: sales@freqdev.com • Web Address: http://www.freqdev.com

Product Handling

Procedure

Programmable Filter Modules Power Sequence & ESD

November 2000

Programmable Filters Modules

818, 824, 828, 828BP, 828BR, 854, 858, R854, R858

I. Scope

The following precautions are necessary when handling and installing Frequency Devices

programmable filter modules.

II. Digital Circuit Description

The digital input pins connect directly to 4000 series CMOS logic, such as the 4053 analog switch. The

power supply (Vss) for the digital logic on the module comes directly from the +15 Volt pin on the

module. This sets the threshold voltage at 11.0 V minimum to 15.0 V maximum for a "1" (High) level

and 0.0 V minimum to 4.0 V maximum for a "0" (Low) level. Applying a voltage between 4.0 and 11.0

V will produce unpredictable operation. Connecting 5 Volt or 3.3 V logic devices directly to the filter

module without using a voltage translator will result in erratic operation of the filter.

III. (VERY IMPORTANT) Power-Up and Power-Down Sequence

Do not plug-in or un-plug module while power is applied.

It is imperative that power is

supplied to the + 15 V pin on the filter module before or at the same instance that any digital pin is

pulled High (> 0.0 V). Failure to do this will result in excessive current flowing through the digital input

pin and through a protection diode internal to the 4000 logic, which will result in damage to the module.

The proper power-up and power-down sequence is:

1. Connect filter module ground.

2. Connect filter module +15 V.

3. Connect filter module -15 V.

4. Connect the input signal.

All four of the above steps can also occur simultaneously. Power-down should occur in the reverse

order.

IV. ESD Issues

Like most modern electronic equipment, the modules can be damaged by electrostatic discharge (ESD).

The modules are shipped from the factory in sealed, anti-static packaging and should be kept in the

sealed package prior to mounting on a circuit board. The following additional rules should also be

observed when handling the modules after they are removed from the factory packaging:

1. Only a person wearing a properly grounded wrist strap should handle the modules.

2. Any work surface that the modules are placed on must be properly ESD grounded.

3. Any insulating materials capable of generating static charge (such as paper) should be kept

away from the modules.

Static generating clothing should be covered with an ESD-protective smock.

25 Locust St, Haverhill, Massachusetts 01830 • Tel: 800/252-7074, 978/374-0761 • FAX: 978/521-1839

e-mail: sales@freqdev.com • Web Address: http://www.freqdev.com

Recommended Resources

Low noise video amplifier circuit with very small input capacitance

Precision absolute converter circuit with wide dynamic range

SMAT LRT-260A hot and cold water dispenser circuit diagram

Video amplifier circuit: video amplifier board-4

Time scale sawtooth wave generation circuit

Computer motherboard circuit diagram 810 2_05

Shared resource management: This chapter mainly manages shared resources based on the API functions provided by Raw OS. A shared resource is usually a global variable, such as a static or non-static global variable, a global arr...; 凌海滨 Embedded System

The continuous construction of the capability center is a strong guarantee for PDT work: The new product development team (PDT) is mainly composed of representatives from various functional departments such as procurement, manufacturing, and development. The implementation and improvement...; eeleader Talking about work

I beg you to give me the source code, I need it urgently!: Use keyboard keys, LED lights, and digital tubes to simulate the elevator operation process. Assume that there are 8 floors. Keyboard keys 1-8 are used to enter the desired floor. 8 LEDs display the d...; 王贺贺 51mcu

Urgent, please help me: I am developing an instrument now, which uses a 320×240 EL screen with a high refresh rate. I don't know whether to use ARM or DSP, nor which operating system to use. Please give me some advice....; 184848715 Embedded System

【NXP Rapid IoT Review】W3 Environmental Data Collection: [size=14px]In the W2 review, the author used the existing samples to introduce the general environment of the web IDE. But if you want to use this environment to implement your own development, what s...; johnrey RF/Wirelessly

About TCPMP UI Modification: I am currently researching a TCPMP project and now want to give it a nice interface. If anyone has done this, please contact me for cooperation. EMAIL: mobile_search@163.com, MSN: mobile_search@hotmai...; goldfree Embedded System

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components