EEWORLDEEWORLDEEWORLD

Part Number

Search

P7-3321-FHT-47

Description
Rectangular Power Connector, 21 Contact(s), Male, Wire Wrap Terminal, Plug
CategoryThe connector    The connector   
File Size637KB,8 Pages
ManufacturerMolex
Websitehttps://www.molex.com/molex/home
Download Datasheet Parametric View All

P7-3321-FHT-47 Overview

Rectangular Power Connector, 21 Contact(s), Male, Wire Wrap Terminal, Plug

P7-3321-FHT-47 Parametric

Parameter NameAttribute value
MakerMolex
Reach Compliance Codeunknow
Other featuresPOLARIZED
Body/casing typePLUG
Connector typeRECTANGULAR POWER CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact point genderMALE
Contact materialBRASS
DIN complianceNO
empty shellNO
Filter functionNO
IEC complianceNO
MIL complianceNO
Manufacturer's serial number3300
Mixed contactsNO
Installation typeCABLE AND PANEL
OptionsGENERAL PURPOSE
Shell materialPLASTIC
Termination typeWIRE WRAP
Total number of contacts21
Questions about AD9361
When the AD9361 local oscillator is set to 2400M, assuming that a 2402M signal is collected at this time, then through [/font][/color][color=#4183c4][font=微软雅黑][url=http://bbs.elecfans.com/zhuti_fpga_...
dreamandactual Analog electronics
Chip dedicated heat sink
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:00[/i] MAP series high thermal conductivity soft silicone thermal insulation pads are widely used in electronic equipment industries su...
warxp990 Mobile and portable
I made a board and found it can't start using Jun Yixing's u-boot
I made a board and used Junyixing SD card burning method to burn uboot, kernel, and file system into nand flash. But after switching to nand flash to start, I found that uboot did not print any inform...
bailyzheng Embedded System
Does HAL_Init() require any other initialization work?
When generating an STM32 project with STM32CubeMX, I found that the port initialization work was not completed. ----------------------- The routines provided by ST are also like this:In HAL_Init(), no...
dontium stm32/stm8
After the development board is started, I can enter the general user but cannot enter the root. What should I do?
Question: My development board can start normally, but after startup it is $, not #. I entered an ordinary user panws, but don't know how to become the root user. The su and useradd commands cannot be...
问渠 Embedded System
【KW41z】The wireless alarm system test board has been soldered. I don't know how the debugging will go.
【KW41z】The wireless alarm system test board has been soldered. I wonder how the debugging will go:surrender:...
damiaa NXP MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 748  1836  267  208  122  16  37  6  5  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号