EEWORLDEEWORLDEEWORLD

Part Number

Search

AZ576-1C-24DE

Description
20A MINIATURE POWER RELAY
File Size1MB,2 Pages
ManufacturerAZETTLER
Websitehttp://www.azettler.com/
Download Datasheet View All

AZ576-1C-24DE Overview

20A MINIATURE POWER RELAY

20A MINIATURE
POWER RELAY
FEATURES
Class F standard
Dielectric strength 5000Vrms
Low cost
Epoxy sealed versions available
20 Amp switching
UL
E44211
TUV
50333135
CONTACTS
Arrangement
Ratings
SPST (1 Form
A)
SPDT (1 Form
C)
Resistive load:
Max. switched power:
510W or 5540VA
Max. switched current:
20A
Max. switched voltage:
30VDC
or
277VAC
*
Note: If switching voltage is greater than 30 VDC, special
AZ
AZ576
GENERAL DATA
Life Expectancy
Mechanical
Electrical
Operate Time (Max)
Release Time (Max)
Minimumoperations
1 x 10
7
ops Min. (no load)
1 x 10
5
ops Min.
(rated load)
15ms at nominal coil voltage (<8ms typ)
8ms at nominal coil voltage (<4ms typ)
(with no coil suppression)
precautions must be taken. Please contact the factory.
Rated Load
UL, CUR
20A at 277VAC Resistive, 30k cycles, 85°C
5A at 120/277VAC Pilot Duty, 30k cycles, 85°C
1HP at 120/240/480VAC, 100k cycles, 40°C
10FLA / 60LRA at 250VAC, 100k cycles, 40°C
Dielectric Strength
5000Vrms coil to contact
(at sea level for 1 min.)
1000Vrms between open contacts
Surge Voltage
coil-contacts
Insulation
Resistance
Dropout
Ambient Temperature
Operating
Storage
Vibration
Shock
Enclosure
Terminals
Max. Solder Temp.
Max. Solder Time
10kV (1.2/50µs)
1000 megohms min. at 20°C
500 VDC 50% RH
Greater than 10% of nominal coil voltage (DC)
At nominal coil voltage
-40°C (-40°F) to 105°C (221°F)
-40°C (-40°F) to 130°C (266°F)
1.5mm DA at 10–55 Hz
10 g
P.B.T. polyester
Tinned copper alloy, P. C.
270°C (518°F)
5 seconds
80°C (176°F)
30 seconds
12 grams
(N.O.)
20A at 120VAC Resistive, 100k cycles, 65°C
17A at 277VAC/30VDC Resistive, 100k cycles, 105°C
16A at 277VAC Resistive, 100k cycles, 105°C
16A at 120/277VAC General Use, 85°C
8A at 120VAC Tungsten, 30k cycles, 85°C
5A at 120VAC
Ballast, 25k
cycles,
85°C
1.5HP at 120VAC Motor, 100k cycles, 85°C
TV-5 120VAC, 25k (N.O. only),
85°C
TV-8 120VAC, 25k (N.O. only),
40°C.
Steady state current 8A, min. inrush (peak) current 117A
(N.C.)
17A at 277VAC/30VDC Resistive, 100k cycles, 105°C
16A at 120/277VAC General Use, 30k cycles, 85°C
TÜV
Material
Resistance
17A at 277VAC / 30VDC Resistive, 100k cycles, 105°C
Silver Tin-Oxide
Initial 100
milliohms
max.
at
6VDC, 1A
COIL
Power
At Pickup Voltage
(typical)
Max. Continuous
Dissipation
Temperature Rise
Max. Temperature
225mW, (DC, standard)
Max. Solvent Temp.
Max. Immersion Time
1.7W at 20°C (68°F) ambient
26°C (47°F) at nominal coil voltage
17°C (31°F) at nominal coil voltage, sensitive coil
130°C (266°F)
Weight
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
5/16/16
Show the process of WEBENCH design + laptop power supply design
This design uses a 220V AC power supply and outputs a 19V DC power supply for laptops....
gaoyang9992006 Analogue and Mixed Signal
I am new to layout. I have detailed allegro software installation steps. What is the success rate?
Take the installation steps of Cadence Allegro software as an example; Step 1: Insert the CD and execute automatically (or execute setup.exe) to enter the main installation interface.Step 2: Install t...
kdyhdl PCB Design
32.768KHz crystal oscillator
32.768KHz is a standard frequency. The oscillation signal generated by the 32.768KHz clock crystal is divided 15 times by the internal divider of the quartz clock to get the 1Hz second signal, that is...
唐辉电子92 MCU
[Help] About the external interrupt INT0 of C8051F040
I want to use P3.0 of C8051F040 as external interrupt pin - INT0. I have observed the waveform on the pin with an oscilloscope and everything is normal, but I can't enter the external interrupt servic...
38824520 Embedded System
Newbie help - Why does the assembly instruction written in CCS always prompt error?
I just started learning DSP course, and I wrote the code according to the book, but I always get the error when writing in assembly, "TEXTxf.asm", ERROR! at line 15: [E0002] Invalid instruction for sp...
xwy0550123 DSP and ARM Processors
If the lift table you buy has a hidden camera, but the manufacturer does not inform you in advance, do you make a profit or a loss?
Not long ago, a consumer complained that the digital internal screen of the Levo a9 smart lift table he bought contained a hidden camera, but the brand did not inform him in advance and there was no n...
赵玉田 Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 43  2657  1132  2065  2074  1  54  23  42  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号