Features ....................................................................................................................................................................................... 1
Ordering Information .................................................................................................................................................................... 2
LVPECL and FlexSwing Termination .................................................................................................................................. 17
LVDS, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 18
HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 18
Low-power HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V.................... 18
Dimensions and Patterns ― 2.0 x 1.6 mm x mm ....................................................................................................................... 19
Dimensions and Patterns ― 2.5 x 2.0 mm x mm ....................................................................................................................... 20
Dimensions and Patterns ― 3.2 x 2.0 mm x mm ....................................................................................................................... 21
Revision History ......................................................................................................................................................................... 22
Rev 0.52
Page 3 of 23
www.sitime.com
SiT9375
Low Jitter Differential XO for Standard Frequencies
Electrical Characteristics
ADVANCED
All Min and Max limits in the Electrical Characteristics tables are specified over operating temperature and rated operating
voltage with standard output termination shown in the termination diagrams. Typical values are at 25°C and nominal
supply voltage.
Table 3. Electrical Characteristics – Common to All Output Signaling Types
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
–
Min.
Typ.
Max.
Unit
MHz
ppm
Condition
Refer to frequencies listed in
Ordering Information
section.
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and 10 years
aging at 25°C
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and first year aging
at 25°C
Ambient temperature of 25°C
Extended commercial, ambient temperature
Industrial, ambient temperature
Ambient temperature
Extended industrial, ambient temperature
Voltage-supply order code “YY”
Voltage-supply order code “XX”
Voltage-supply order code “18”.
Contact SiTime
for 1.5 V
Voltage-supply order code “25”
Voltage-supply order code “33”
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
See
Figure 5
and
Figure 7
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin toggles to enable logic level to
the time clock pins reach 90% of swing. See
Figure 12
Measured from the time OE pin toggles to disable logic level to
the last clock edge. See
Figure 13
12 kHz to 20 MHz offset frequency integration bandwidth,
156.25 MHz
12 kHz to 20 MHz offset frequency range, 156.25 MHz
12 kHz to 20 MHz offset frequency range, 155.52 MHz
156.25 MHz
156.25 MHz
Frequency Range
Standard frequencies
–
±20
Frequency Stability
–
–
–
10 Year Aging
Operating Temperature Range
F_10y
T_use
–
-20
-40
-40
-40
Supply Voltage
Vdd
1.71
2.25
1.71
2.25
2.97
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Startup Time
Output Enable Time
Output Disable Time
VIH
VIL
Z_in
DC
T_start
T_oe
T_od
70%
–
–
45
–
–
–
–
–
–
±1
–
–
–
–
–
–
1.80
2.50
3.30
–
–
100
–
1
–
–
±25
±30
±50
–
+70
+85
+95
+105
ppm
ppm
ppm
ppm
°C
°C
°C
°C
V
V
V
V
V
Temperature Range
Supply Voltage
3.63
3.63
1.89
2.75
3.63
Input Characteristics
–
Vdd
30%
–
55
5
100+3 clock
cycles
100+3 clock
cycles
Vdd
kΩ
%
ms
ns
ns
Output Characteristics
Startup, OE and SE Timing
Jitter and Phase Noise
RMS Phase Jitter (random)
Spurious Phase Noise
RMS Period
Jitter
[1]
Jitter
[1]
T_phj
PN_spur_a
PN_spur_b
T_jitt_per
T_jitt_cc
Peak Cycle-to-cycle
–
–
–
–
–
200
-110
-80
1
6
–
–
–
–
–
fs
dBc
dBc
ps
ps
Note:
1. Measured according to JESD65B.
Rev 0.52
Page 4 of 23
www.sitime.com
SiT9375
Low Jitter Differential XO for Standard Frequencies
ADVANCED
Table 4. Electrical Characteristics – LVPECL
|
Supply voltages: 2.5 V
±10%,
3.3 V
±10%,
2.25 V to 3.63 V
Parameter
Current Consumption, Output
Enabled without Termination
Current Consumption, Output
Enabled with Termination 1
Current Consumption, Output
Enabled with Termination 2
Current Consumption, Output
Disabled without Termination
Current Consumption Output
Disabled with Termination 1
Current Consumption, Output
Disabled with Termination 2
OE Leakage Current
Symbol
Idd_oe_nt
Idd_oe_wt1
Idd_oe_wt2
Idd_od_nt
Idd_od_wt1
Idd_od_wt2
I_leak
Min.
–
–
–
–
–
–
–
Typ.
43
52
71
58
58
86
37
Max.
–
–
–
–
–
–
–
Unit
mA
mA
mA
mA
mA
mA
mA
Condition
Excluding load termination current
Including load termination current. See
Figure 15
for
termination
Including load termination current. See
Figure 18
for
termination
Excluding load termination current
Including load termination current. See
Figure 15
for
termination
Including load termination current. See
Figure 18
for
termination
OE = disable logic, DC termination, OUTP and OUTN held
Author: Huang Gang, member of YiBo Technology ExpresswayFrom the simulation results of the previous article, a pair of differential lines can indeed control impedance well by returning to each other. ...
Delta PLC, touch screen, inverter, in a system based on RS-485 interface communication. Touch screen communication is unstable, no error, other communications are normal. But the touch screen and PLC ...
The leader has assigned a task to me, and I am a novice. I am here to ask for your advice. I would be grateful. In the field, the operating data of some equipment is transmitted to the company's compu...
As the title says, what are some handwriting input methods under WinCE6.0? Has anyone tried it before? Can you give me some advice? What is the name? Full screen/partial screen? Open source/commercial...
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
LED lighting: Basic circuit design can be completed in as little as one day
Semiconductor manufacturers are also getting involved in the LED lighting business. The power circuit of LED req...[Details]
Currently, each country is developing its own USB interface
charging specifications
, which leads to a major problem that a USB interface
charging
device manufactured in one country...[Details]
The DisplayPort interface standard is approved by the Video Electronics Standards Association (VESA) to provide an open, scalable standard for the entire industry. The development of DisplayPort ca...[Details]
The ARINC429 bus is one of the most commonly used communication buses between various subsystems of avionics. As the "skeleton" of modern avionics systems, once the bus system or the attached airbo...[Details]
HL201A is a special thick film driver integrated circuit with a capacity of less than 75AGTR developed by Xi'an Power Electronics Technology Research Institute. The article explains the pin arrange...[Details]
introduction
Belt drive is a common transmission device used in industrial production. Its commonly used speed detection device is a photoelectric encoder installed at the rotating end of th...[Details]
Fairchild's FAN6208 is a synchronous rectification (SR) controller for isolated LLC or LC resonant converters that can drive two individual SR MOSFETs emulating the behavior of rectifier diodes. FAN62...[Details]
Some people think: as long as the program runs well, it doesn't matter how the original program is written. But this is absolutely not the case. Software is not completed in one go, and it is neces...[Details]
Previously used primarily in high-power power supplies and large industrial and consumer power supplies, supercapacitors are now finding their way into products of all sizes, especially portable de...[Details]
First, the choice of charging location. Wireless charging technology is related to the distance and state of the charger and the charged device. That is to say, the distance between the two cannot...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
