EEWORLDEEWORLDEEWORLD

Part Number

Search

B41252A8188M062

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 63V, 20% +Tol, 20% -Tol, 1800uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size393KB,21 Pages
ManufacturerTDK Corporation
Websitehttp://www.tdk.com
Environmental Compliance
Download Datasheet Parametric View All

B41252A8188M062 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 63V, 20% +Tol, 20% -Tol, 1800uF, Through Hole Mount, ROHS COMPLIANT

B41252A8188M062 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerTDK Corporation
package instruction,
Reach Compliance Codecompli
capacitance1800 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter22 mm
dielectric materialsALUMINUM (WET)
leakage current2.268 mA
length30 mm
Manufacturer's serial numberB41252
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
Package formSnap-i
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)63 V
ripple current1640 mA
seriesB41252
surface mountNO
Delta tangent0.15
Terminal shapeSNAP-IN
Aluminum electrolytic capacitors
Snap-in capacitors
Series/Type:
Date:
B41252
November 2012
© EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
V2cpld_spi
[i=s]This post was last edited by paulhyde on 2014-9-15 09:14[/i] V2cpld_spi...
wangwei20060608 Electronics Design Contest
LIS3DH chip problem consultation
[table=98%] [tr][td][color=#444444]Hello everyone, I found a problem when I was doing LIS3DH motion detection. [/color][color=#444444]After configuring the registers of LIS3DH (configuring the motion ...
lskam stm32/stm8
The MCU cannot run in DC-DC mode of BLUENRG-1
In the DC-DC mode of BLUENRG, the voltage output is only about 0.5V, and the output of LDO is also only about 0.5V. The MCU cannot operate normally, and the SWD interface cannot be detected using J-li...
suwithin ST - Low Power RF
My emergency light is fully completed. See the picture.
All the components I used are from MAXIM. Although the workmanship is not very particular, you can take a look at them for reference. The pictures were supposed to be uploaded tomorrow, but because my...
ddllxxrr DIY/Open Source Hardware
How to debug nandflash?? (as the title says software debugging)
Anyone who has done this before, please give me some tips. Thanks....
yangjunweimail Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 903  1936  1785  1623  1351  19  39  36  33  28 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号