Please refer to the M5600_U5600 Installation Manual and M5600_U5600 Software Manual.
Note:
Communication is max 65 feet
TE CONNECTIVITY SENSORS
/// M5600
09/2017
Page 3
M5600
Wireless Pressure Transducer
ORDERING INFORMATION
M5600
–
0 0 0 0 0 2
–
05KP G
Port Material
0
17-4PH
1
316L Stainless Steel
Cleaning
0
No Selection
1
Oxygen clean B40.1 Level IV
2
With Snubber
Battery
0
Without Battery
1
CR2032
2
CR2050
Label Type
0
Adhesive Label
1
Laser Marking
Pressure Port
2
1/4-19 BSPP
3
G3/8 JIS B2351
7/16-20UNF Male SAE J1326-2
4
Straight Thread O-Ring BUNA-N
90SH-904
5
1/4-18 NPT
6
1/8-27 NPT
B
G1/4 JIS B2351
E
1/4-19 BSPT
F
1/4-19 BSPP Female w/o Snubber
7/16-20 UNF Female SAE J513
P
Straight Thread
7/16-20 UNF Female SAE J513
N
Straight Thread
M10x1.0mm
Q
ISO 6149-2
M12x1.5mm
S
ISO 6149-2
G1/4 DIN 3852 Form E Gasket
U
DIN3869-14 NBR
M20x1.5mm
W
ISO6149-2
M14x1.5mm
G
ISO6149-2
Pressure Type
G
Gauge
S
Sealed
C
Compound
Compound pressure range is -14.7 to xxxpsig or -1 to xxxbarg.
(e.g. 200PC: -14.7 to 200psig, 020BC: -1 to 20barg)
Pressure Range [psi]
psi
STD
050P
100P
200P
300P
500P
01KP
03KP
05KP
07KP
10KP
15KP
bar
STD
3.5B
007B
010B
020B
035B
070B
200B
350B
500B
700B
01KB
NORTH AMERICA
Measurement Specialties, Inc.,
a TE Connectivity Company
Phone: 800-522-6752
Email:
customercare.frmt@te.com
EUROPE
Measurement Specialties (Europe), Ltd.,
a TE Connectivity Company
Phone: +31 73 624 6999
Email:
customercare.lcsb@te.com
ASIA
Measurement Specialties (China), Ltd.,
a TE Connectivity Company
Phone: 0400-820-6015
Email:
customercare.shzn@te.com
TE.com/sensorsolutions
Measurement Specialties, Inc., a TE Connectivity company.
Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to herein
might be trademarks of their respective owners.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes
no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard
Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse
of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application.
[size=4]What is the difference between the POR signal and the PUC signal in the MSP430F149 microcontroller? What operations does the microcontroller perform after detecting these two signals? Thank yo...
[size=4]The precision of floating point numbers is determined by the number of digits in the mantissa. Most numbers will have errors when expressed as floating point numbers. These errors are small an...
This is an interesting interview with Liu Huijun, Vice President of Chery Research Institute, posted by Electronic Engineering World today. [url]https://www.eeworld.com.cn/news/car/200802/article_1796...
[i=s]This post was last edited by paulhyde on 2014-9-15 03:07[/i] I downloaded it with Xunlei, and it was just a web link. When I opened it, it said I was not logged in and had no rights to download. ...
1. Introduction to SPI bus
SPI (serial peripheral interface) bus technology is a synchronous serial interface introduced by Motorola. It is used for full-duplex, synchronous serial communication betwe...
Newbies please come in and sign up so that we can exchange experiences later!!! I have only learned M51 for more than a week and I am absolutely a novice in learning STM32. Fortunately, the masters an...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
The data collector of the automatic weather station is generally designed based on a single-chip microcomputer or a PC/104 bus controller. It has the characteristics of good compatibility with PC, low...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
In recent years, with the rapid development of the information industry, dot matrix LED display screens have been widely used in various advertising and information display systems such as the fina...[Details]
1 Introduction
There have been many studies on the detection and protection of power grid short circuit and line fault. The short circuit, overload and overvoltage protectors on the market have ...[Details]
Single-chip microcomputers are widely used because of their small size, powerful functions and low price. This article introduces the method of designing a micro electronic piano using the AT89C51 sin...[Details]
Today, the value of electronic components in cars accounts for 15-20% of the total vehicle. In the future, this proportion may be as high as 30-40% as more safety electronics, fuel consumption and ...[Details]
LED lighting: Basic circuit design can be completed in as little as one day
Semiconductor manufacturers are also getting involved in the LED lighting business. The power circuit of LED req...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
The above is to use MB1404 as a stereo composite signal transmitter. You can use the internal high-frequency amplifier and oscillator or not! According to my experience, I still recommend beginners...[Details]