EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN0805K2771BST

Description
Fixed Resistor, Thin Film, 0.2W, 2770ohm, 100V, 0.1% +/-Tol, -100,100ppm/Cel, 0805,
CategoryPassive components    The resistor   
File Size98KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

PTN0805K2771BST Overview

Fixed Resistor, Thin Film, 0.2W, 2770ohm, 100V, 0.1% +/-Tol, -100,100ppm/Cel, 0805,

PTN0805K2771BST Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerVishay
Reach Compliance Codecompli
ECCN codeEAR99
structureChi
JESD-609 codee3
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.609 mm
Package length2.032 mm
Package formSMT
Package width1.27 mm
method of packingTR
Rated power dissipation(P)0.2 W
resistance2770 Ω
Resistor typeFIXED RESISTOR
seriesPTN
size code0805
technologyTHIN FILM
Temperature Coefficient-100,100 ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrie
Tolerance0.1%
Operating Voltage100 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Moisture resistant
High purity alumina substrate
Non-standard values available
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Compliant to RoHS directive 2002/95/EC
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic E of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
Coating
Nickel
Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 30 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE (Ω)
20 to 35K
20 to 65K
20 to 130K
10 to 80K
10 to 301K
10 to 301K
50 to 600K
10 to 1M
10 to 1M
10 to 1.75M
10 to 2M
10 to 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 02-Nov-09
For technical questions, contact:
thin-film@vishay.com
www.vishay.com
55
How to enable TMU of 28377d.
According to the PDF instructions, TMU is enabled in the project settingsBut when checking math.h in the program, I found #if defined(__TMS320C28XX_TMU__)!__TI_STRICT_FP_MODE__ The contents below are ...
bingtuohun DSP and ARM Processors
VGA display system under OV7670 camera
Ready to use...
梦一般的虚幻 FPGA/CPLD
RMB Urgently looking for GIF to reduce the number of colors and the same area of transparency compression DLL or COM component
RMB Urgently looking for GIF to reduce the number of colors and the same area transparent compression (DLL or COM component) Requirements: GIF has about 5 frames, each frame is an image, and the same ...
liyz2169 Embedded System
I'm a newbie asking, why can't my program enter the interrupt?
I wrote a small program, intending to control the eight LED lights on the board by outputting eight numbers from 1 to 8 through the serial port control software on the computer. The lights are common ...
zhonghxun 51mcu
About the wireless buzzer made with AT89C51
I want to ask the experts, I use AT89C51 to make a wireless buzzer, and use Protuse to simulate it. Which chip should be used for its wireless transmitting circuit and wireless receiving circuit? How ...
nimeia 51mcu
MSP430F4XX series serial port burning program help
I'm developing msp430F4152 recently. Now the product needs to upgrade the program code through the serial port (only RXD and TXD lines). I know that the BSL code (0xc00~0xfff) is fixed inside 430. Acc...
西小屯 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 152  200  240  392  2667  4  5  8  54  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号