EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN1010E2520BBWS

Description
RESISTOR, THIN FILM, 0.5 W, 0.1 %, 25 ppm, 252 ohm, SURFACE MOUNT, 1010, CHIP
CategoryPassive components    The resistor   
File Size117KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

PTN1010E2520BBWS Overview

RESISTOR, THIN FILM, 0.5 W, 0.1 %, 25 ppm, 252 ohm, SURFACE MOUNT, 1010, CHIP

PTN1010E2520BBWS Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerVishay
package instructionSMT, 1010
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresANTI-SULFUR; LASER TRIMMABLE; NON-INDUCTIVE
structureRectangul
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.838 mm
Package length2.667 mm
Package formSMT
Package width2.54 mm
method of packingWaffle Pack
Rated power dissipation(P)0.5 W
Rated temperature70 °C
resistance252 Ω
Resistor typeFIXED RESISTOR
size code1010
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrie
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage150 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Pb-free
Moisture resistant
Available
High purity alumina substrate
RoHS*
Non-standard values available
COMPLIANT
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic H of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
coating
Nickel barrier
High Purity
Alumina Substrate
Adhesion layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 25 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE - (Ω)
20 - 35K
20 - 65K
20 - 130K
10 - 80K
10 - 301K
10 - 301K
50 - 600K
10 - 1M
10 - 1M
10 - 1.75M
10 - 2M
10 - 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 23-Jan-09
For technical questions, contact: thin-film@vishay.com
www.vishay.com
55
How to Improve the Anti-interference Performance of Single Chip Microcomputer System
Friends who have worked on products have all experienced that a design seems simple, and the hardware design and code writing can be done quickly, but there are more or less accidents during the debug...
jingmindm Embedded System
LOTO virtual oscilloscope about trigger sensitivity function
The trigger level is just a reference voltage, but the actual waveform has jitter at the edge. The following figure is a screenshot of a normal rising edge trigger:The blue T line is the reference vol...
LOTO2018 Test/Measurement
Problems with CPLD driving DS18B20
I wrote a program to drive DS18B20 with CPLD and use LCD1602 for display. But it always displays 00.0. Can an expert take a look at my code to see if there is a problem? Thank you!...
chenbingjy FPGA/CPLD
How to use 8050 transistor to amplify the weak current of hand touch to 0.5 watt with 3V voltage without op amp
How to use 8050 transistor to amplify the weak current of hand touch to 0.5 watt with 3V voltage without op amp [[i] This post was last edited by boofeng2002 on 2012-4-8 09:51 [/i]]...
boofeng2002 Analog electronics
Looking for a minimum system diagram for MSP430f21X1
Looking for a minimum system diagram for MSP430f21X1...
ifree6 Microcontroller MCU
Did you successfully retrieve your password?
I changed my password some time ago. When I logged out and logged in again this afternoon, I forgot my password, so I used the password recovery function, but I didn't find any email. Fortunately, I r...
wangfuchong Suggestions & Announcements

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2108  1279  491  2868  2460  43  26  10  58  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号