EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN2208H1930BGTS

Description
RESISTOR, THIN FILM, 0.75 W, 0.1 %, 50 ppm, 193 ohm, SURFACE MOUNT, 2208, CHIP, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size117KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance  
Download Datasheet Parametric View All

PTN2208H1930BGTS Overview

RESISTOR, THIN FILM, 0.75 W, 0.1 %, 50 ppm, 193 ohm, SURFACE MOUNT, 2208, CHIP, ROHS COMPLIANT

PTN2208H1930BGTS Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerVishay
package instructionSMT, 2208
Reach Compliance Codecompli
ECCN codeEAR99
Other featuresANTI-SULFUR; LASER TRIMMABLE; NON-INDUCTIVE
structureRectangul
JESD-609 codee4
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.838 mm
Package length5.309 mm
Package formSMT
Package width2.489 mm
method of packingTR
Rated power dissipation(P)0.75 W
Rated temperature70 °C
resistance193 Ω
Resistor typeFIXED RESISTOR
size code2208
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceGold (Au) - with Nickel (Ni) barrie
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage150 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Pb-free
Moisture resistant
Available
High purity alumina substrate
RoHS*
Non-standard values available
COMPLIANT
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic H of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
coating
Nickel barrier
High Purity
Alumina Substrate
Adhesion layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 25 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE - (Ω)
20 - 35K
20 - 65K
20 - 130K
10 - 80K
10 - 301K
10 - 301K
50 - 600K
10 - 1M
10 - 1M
10 - 1.75M
10 - 2M
10 - 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 23-Jan-09
For technical questions, contact: thin-film@vishay.com
www.vishay.com
55
Urgently need to transfer the data collected by the EEG sensor to the MSP430f149
The EEG sensor has built-in Bluetooth. I put another Bluetooth on the microcontroller, and the Bluetooth matching was successful. However, there was a problem with the data transmission. I don’t know ...
漩涡中的鲨鱼 Microcontroller MCU
A grammar question for beginners
[align=left]a>8, is there any grammatical problem in this sentence:time:[/align]eeworldpostqq...
JFET FPGA/CPLD
Why doesn't the buzzer sound?
module fp_verilog(clk,reset_n,fm); input clk,reset_n; output fm; reg fm; reg [19:0] counter; always@(posedge clk or negedge reset_n)if(!reset_n)counter=20'b0;elsebeginif(counter[19])beginfm=1'b1;count...
leomeng FPGA/CPLD
What are the wireless network protocols commonly used in embedded systems?
I am a newbie, I want to ask what are the commonly used embedded wireless network protocols? Give some specific examples, thank you....
milkcowboy Embedded System
[Repost] Things that hardware engineers should pay attention to in hardware development
Things that hardware engineers should pay attention to in hardware development (Abstract) When starting a hardware development project, the original driving force will come from many aspects, such as ...
linda_xia Analog electronics
SIP protocol in linux
From EEWORLD cooperation group: arm linux fpga embedded 0 (49900581) Group owner: wangkj...
四季未央 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2729  321  599  2274  305  55  7  13  46  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号