EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN2512K1802BBT

Description
Fixed Resistor, Thin Film, 1W, 18000ohm, 200V, 0.1% +/-Tol, -100,100ppm/Cel, 2612,
CategoryPassive components    The resistor   
File Size98KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

PTN2512K1802BBT Overview

Fixed Resistor, Thin Film, 1W, 18000ohm, 200V, 0.1% +/-Tol, -100,100ppm/Cel, 2612,

PTN2512K1802BBT Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerVishay
Reach Compliance Code_compli
ECCN codeEAR99
structureChi
JESD-609 codee0
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.609 mm
Package length6.578 mm
Package formSMT
Package width3.149 mm
method of packingTR
Rated power dissipation(P)1 W
resistance18000 Ω
Resistor typeFIXED RESISTOR
seriesPTN
size code2612
technologyTHIN FILM
Temperature Coefficient-100,100 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb) - with Nickel (Ni) barrie
Tolerance0.1%
Operating Voltage200 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Moisture resistant
High purity alumina substrate
Non-standard values available
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Compliant to RoHS directive 2002/95/EC
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic E of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
Coating
Nickel
Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 30 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE (Ω)
20 to 35K
20 to 65K
20 to 130K
10 to 80K
10 to 301K
10 to 301K
50 to 600K
10 to 1M
10 to 1M
10 to 1.75M
10 to 2M
10 to 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 02-Nov-09
For technical questions, contact:
thin-film@vishay.com
www.vishay.com
55
Has anyone used F28035 or F28027 to perform FFT?
I recently wanted to do some FFT processing. I read the principle and looked for the program. Finally, I found that TI's DSP library is quite convenient. But now the problem has come out. The library ...
dontium Microcontroller MCU
lm3s9b96 External SDRAM hardware receiver
Dear experts, the schematic diagram provided by TI shows that the external 16-bit SDRAM is connected to the CPU's A0 and the SDRAM's A0. Why is it not the CPU's A1 connected to the SDRAM's A0?...
bwl19881019 Microcontroller MCU
[AVR compilation problem] DS1302 program problem
When I was writing a ds1302 program, the following problem occurred : c:/winavr-20100110/bin/../lib/gcc/avr/4.3.3/../../../../avr/bin/ld.exe: cannot find -lC:\WinAVR-20071221\avr\include\avr\io make: ...
eeleader Microchip MCU
Error compiling the first C2000 program. (Solved. Correct answer on the 9th floor)
After I created a new project, I clicked on the project settings and added the header file to the project (pictured above). I had installed controlSUITE. Then I wrote the following program, following ...
qinkaiabc Microcontroller MCU
Help, LM3S9B96 in KEIL environment, DEBUG mode peripherals only have core peripherals
I need help. In the KEIL environment, the peripherals of LM3S9B96 in DEBUG mode are only core peripherals. Other ADC and I/O are invisible. I would like to ask the experts, why is this? I am doing har...
njawo Microcontroller MCU
What is the difference between W(b) and b in assembly language?
I was looking at the Linux source code recently. I had never touched assembly language before. When I saw the interrupt vector table, I wanted to understand the assembly code. I found that b stands fo...
flashtt Linux and Android

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 444  556  2460  219  1249  9  12  50  5  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号