RCG0201...C e3
www.vishay.com
Vishay
Green Commodity Thick Film Chip Resistors
FEATURES
• High volume product suitable for commercial
applications
• Green resistor - does not use exemptions
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
TECHNICAL SPECIFICATIONS
DESCRIPTION
Imperial size
Metric size code
Resistance range
Resistance tolerance
Temperature coefficient
Rated dissipation,
P
70 (1)
Operating voltage,
U
max.
AC
RMS
/DC
Permissible film temperature,
F max. (1)
Operating temperature range
Max. resistance change at
P
70
for resistance range, |R/R| after:
1000 h
Permissible voltage against ambient (insulation):
1 min,
U
ins
Note
(1)
Please refer to APPLICATION INFORMATION below
50 V
3.0 %
RCG0201...C e3
0201
RR0603M
15
to 1 M; jumper (0
)
± 5 %; ± 1 %
± 250 ppm/K
0.05 W
25 V
125 °C
-55 °C to +125 °C
APPLICATION INFORMATION
When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal
resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted
film temperature is not exceeded.
These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift
increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a
functional lifetime.
TEMPERATURE COEFFICIENT AND RESISTANCE RANGE
TYPE / SIZE
TCR
± 250 ppm/K
Jumper,
I
max.
= 0.5 A
TOLERANCE
±5%
±1%
50 m
RESISTANCE
15
to 1 M
15
to 1 M
0
E-SERIES
E24
E24; E96
-
RCG0201...C e3
Note
• The temperature coefficient of resistance (TCR) is not specified for 0
jumpers
Revision: 16-Feb-18
Document Number: 20068
1
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
RCG0201...C e3
www.vishay.com
Vishay
PACKAGING
TYPE / SIZE
CODE
ED = ET7
RCG0201...C e3
EI = ET2
EE = EF4
QUANTITY
10 000
20 000
50 000
Paper tape acc.
to IEC 60068-3
Type I
8 mm
2 mm
PACKAGING
STYLE
WIDTH
PITCH
PACKAGING
DIMENSIONS
Ø 180 mm/7"
Ø 254 mm/10"
Ø 330 mm/13"
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: RCG02011K00FREDC
R
C
G
0
2
0
1
1
K
0
0
F
R
E
D
C
TYPE / SIZE
RCG0201
RESISTANCE
R
= decimal
K
= thousand
M
= million
0000
= jumper
TOLERANCE
F
= ± 1.0 %
J
= ± 5.0 %
Z
= jumper
TCR
R
= ± 250 ppm/K
0
= jumper
PACKAGING
ED
EE
EI
SPECIAL
Up to 2 digits
C
= commodity
PRODUCT DESCRIPTION: RCG0201-C 250 1K0 1 % ET7 e3
RCG0201-C
TYPE / SIZE
RCG0201-C
250
TCR
± 250
ppm/K
1K0
RESISTANCE
15R
= 15
1K0
= 1 k
10K
= 10 k
1M0
= 1 M
0R0
= jumper
1%
TOLERANCE
±1%
±5%
ET7
PACKAGING
ET7
EF4
ET2
e3
LEAD (Pb)-FREE
e3
= pure tin
termination finish
VISHAY GREEN REQUIREMENTS
SUBSTANCES
Lead (Pb)
Mercury (Hg)
Cadmium (Cd)
Hexavalent chronium
Polybrominated biphenyl (PBB)
Polybrominated diphenyl ether (PBDE)
Bromine (Br)
Chlorine (Cl)
Sum of bromine and chlorine
Antimony (Sb)
Red phosphorous
CONCENTRATION LIMIT
< 1000 ppm
< 1000 ppm
< 100 ppm
< 1000 ppm
< 1000 ppm
< 1000 ppm
< 900 ppm
< 900 ppm
1500 ppm max.
< 900 ppm
< 100 ppm
Notes
• No exemptions (e.g. lead (Pb) in glass) may be applied to any substances or application for the “Vishay Green” category
• All concentration levels are based on homogenous materials
Revision: 16-Feb-18
Document Number: 20068
2
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
RCG0201...C e3
www.vishay.com
DERATING
Axis Title
2nd line
P
- Power Dissipation (W)
0.10
70
10000
Vishay
1000
0.05
100
1st line
2nd line
50
100
125
10
ϑ
amb
- Ambient Temperature (°C)
2nd line
RCG0201...C
0
-50
0
TEST PROCEDURES AND REQUIREMENTS
IEC
EN 60115-1 60068-2
(1)
CLAUSE
TEST
METHOD
TEST
PROCEDURE
Stability for product types:
RCG0201...C e3
4.5
4.8
-
-
Resistance
Temperature
coefficient
Endurance at 70 °C
Endurance at
upper category
temperature
Damp heat,
steady state
Operation at low
temperature
Rapid change
of temperature
-
(20 / -55 / 20) °C and
(20 / 125 / 20) °C
U
=
4.25.1
-
P
70
x
R
or
U
=
U
max.
;
; whichever is less;
1.5 h on; 0.5 h off;
70 °C; 1000 h
125 °C, 1000 h
(40 ± 2) °C;
(93 ± 3) % RH;
56 days
-55 °C; 1 h
30 min. at -55 °C;
30 min. at 125 °C
5 cycles
300 cycles
4.13
-
Short time
overload
U
= 2.5 x
P
70
x
R
2 x
U
max.
;
whichever is the less severe;
5s
Endurance by sweeping;
10 Hz to 2000 Hz; no resonance;
amplitude
1.5 mm or
200 m/s
2
; 7.5 h
Solder bath method;
Sn60Pb40 non-activated flux;
(235 ± 5) °C
(2 ± 0.2) s
4.17
58 (Td)
Solderability
Solder bath method;
Sn96.5Ag3Cu0.5 non-activated
flux;
(245 ± 5) °C
(3 ± 0.3) s
± (0.5 %
R
+ 0.05
)
± (1 %
R
+ 0.05
)
± (2 %
R
+ 0.1
)
±1%
± 250 ppm/K
REQUIREMENTS
PERMISSIBLE CHANGE (R)
15 to 1 M
±5%
± (3 %
R
+ 0.1
)
4.25.3
-
± (2 %
R
+ 0.1
)
4.24
4.36
78 (Cab)
1 (Aa)
± (3 %
R
+ 0.1
)
± (1 %
R
+ 0.05
)
4.19
14 (Na)
4.22
6 (Fc)
Vibration
± (0.5 %
R
+ 0.05
)
Good tinning ( 95 % covered)
no visible damage
Revision: 16-Feb-18
Document Number: 20068
3
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
RCG0201...C e3
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
IEC
EN 60115-1 60068-2
(1)
CLAUSE
TEST
METHOD
TEST
PROCEDURE
Stability for product types:
RCG0201...C e3
4.18
4.29
4.32
4.33
4.7
Note
(1)
REQUIREMENTS
PERMISSIBLE CHANGE (R)
15 to 1 M
± (1.0 %
R
+ 0.05
)
No visible damage
No visible damage
± (1 %
R
+ 0.05
)
No visible damage, no open circuit in bent position
No flashover or breakdown
58 (Td)
45 (XA)
21 (Uu
3
)
21 (Uu
1
)
-
Resistance to
soldering heat
Component solvent
resistance
Shear (adhesion)
test
Substrate bending
Voltage proof
Solder bath method
(260 ± 5) °C;
(10 ± 1) s
Isopropyl alcohol;
50 °C; method 2
RR0603M: 3 N
Depth 2 mm;
3 times
U
= 1.4 x
U
ins
; 60 s
The quoted IEC standards are also released as EN standards with the same number and identical contents
DIMENSIONS
in millimeters
DIMENSIONS AND MASS
TYPE / SIZE
RCG0201...C e3
L
(mm)
0.60 ± 0.05
W
(mm)
0.30 ± 0.05
H
(mm)
0.23 ± 0.05
T1
(mm)
0.15 ± 0.05
T2
(mm)
0.10 ± 0.05
MASS
(mg)
0.17
SOLDER PAD DIMENSIONS
X
G
Y
Z
RECOMMENDED SOLDER PAD DIMENSIONS
REFLOW SOLDERING
TYPE / SIZE
RCG0201...C e3
G
(mm)
0.3
Y
(mm)
0.35
X
(mm)
0.4
Z
(mm)
1.0
Notes
• The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g in standards IEC 61188-5-x
(1)
or
in publication IPC-7351
(1)
The quoted IEC standards are also released as EN standards with the same number and identical contents
Revision: 16-Feb-18
Document Number: 20068
4
For technical questions, contact:
thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 08-Feb-17
1
Document Number: 91000
stm32/stm8
京公网安备 11010802033920号
EEWORLD
