EEWORLDEEWORLDEEWORLD

Part Number

Search

B12JP-JH

Description
TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7
Categoryunclassified   
File Size256KB,8 Pages
ManufacturerOhmite
Websitehttps://www.ohmite.com
Download Datasheet Parametric View All

B12JP-JH Overview

TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7

B12JP-JH Parametric

Parameter NameAttribute value
Lead-freeYes
EU RoHS regulationsYes
stateACTIVE
terminal coatingGOLD OVER NICKEL
Manufacturer SeriesB
Switch typeTOGGLE SWITCH
Series B
Toggles
Process Sealed Subminiature Antistatic Toggles
A
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Rockers
Other Ratings
Programmable Illuminated PB
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Keylocks
Contact Timing:
Angle of Throw:
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum for locking lever models
50,000 operations minimum
Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)
Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)
Toggle L: 0.59N
Nonshorting (break-before-make)
26°
Materials & Finishes
Rotaries
Toggle:
Bushing:
Gasket:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Nickel plated brass
Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing
Nitrile butadiene rubber
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
Tactiles
Slides
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Touch
Installation
Mounting Torque:
.30 ~ .45Nm (2.65 ~ 3.98 lb
in) for A1 actuator with threaded bushing only
PCB Processing
Indicators
Soldering:
Cleaning:
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
Supplement
UL94V-0 available
The B Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A12
www.nkk.com
Newcomer Report
I am a newbie who has just come into contact with single-chip microcomputers and am learning C51 programming. I have some basic knowledge of C++. I would like to ask you if there are any C51 programmi...
tzhbingdu MCU
Question about resetting the number of steps obtained by SensorTile SDK
I'm testing the step count function of Android recently, but I found the following questions. I hope someone can answer them for me: 1. There are two methods in SDK, getFrequency and getSteps, to get ...
李炳1991 MEMS sensors
Lightweight multi-mode mobile phone RF design module
TriQuint Semiconductor released lightweight multi-mode mobile phone RF design modules. Three highly integrated WCDMA modules reduce the RF front-end complexity of 3G mobile phones and place more key f...
JasonYoo RF/Wirelessly
How to use CreateFile to get the serial port handle under wince
00 00 05 00 00 00 10 01 00 00 00 4B 00 00 00 00 08 00 00 0. [HKEY_LOCALMACHINE/drivers/BuildIn/Serial_cmd] (Default): (value not set) Dll: com165550.Dll Tsp: Unimodem.dll IoBase: 2926575616 Irq: 19 Io...
lxg69 Embedded System
Using KITL to debug the network card driver under WINCE5.0, MmmapIOspace function problem
PHYSICAL_ADDRESS phyAddr; phyAddr.QuadPart=pAdapter->m_ulIOBaseAddress; pHardware->m_ulVIoAddr=(ULONG)MmMapIoSpace(phyAddr,256,FALSE); RETAILMSG(TRUE, (TEXT("base virtual address 0x%x"), pHardware->m_...
chinatiger Embedded System
Part 3 - Pointers and array names
1. Access array elements by array name. Look at the following code: int i,a[]={3,4,5,6,7,3,7,4,4,6}; for (i=0;i<=9;i++) { printf ( "%d", a[i]); } Obviously, it displays the value of each element of ar...
mikezhong MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2596  923  2465  2119  2577  53  19  50  43  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号