EEWORLDEEWORLDEEWORLD

Part Number

Search

B18HB-JF

Description
TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7
Categoryunclassified   
File Size256KB,8 Pages
ManufacturerOhmite
Websitehttps://www.ohmite.com
Download Datasheet Parametric View All

B18HB-JF Overview

TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7

B18HB-JF Parametric

Parameter NameAttribute value
Lead-freeYes
EU RoHS regulationsYes
stateACTIVE
terminal coatingGOLD OVER NICKEL
Manufacturer SeriesB
Switch typeTOGGLE SWITCH
Series B
Toggles
Process Sealed Subminiature Antistatic Toggles
A
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Rockers
Other Ratings
Programmable Illuminated PB
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Keylocks
Contact Timing:
Angle of Throw:
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum for locking lever models
50,000 operations minimum
Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)
Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)
Toggle L: 0.59N
Nonshorting (break-before-make)
26°
Materials & Finishes
Rotaries
Toggle:
Bushing:
Gasket:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Nickel plated brass
Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing
Nitrile butadiene rubber
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
Tactiles
Slides
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Touch
Installation
Mounting Torque:
.30 ~ .45Nm (2.65 ~ 3.98 lb
in) for A1 actuator with threaded bushing only
PCB Processing
Indicators
Soldering:
Cleaning:
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
Supplement
UL94V-0 available
The B Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A12
www.nkk.com
About the problem of "usual arithmetic conversion" in C language arithmetic expressions (transferred)
[p=22, null, left][font=Tahoma]During the compilation process of C language arithmetic expressions, there is a problem of "normal arithmetic conversion". In most cases, there is no specific and meanin...
mmmllb Programming Basics
【KW41z】Wireless alarm system test board (using KW41Z's Lierda module) drawing board!
[i=s]This post was last edited by damiaa on 2017-7-5 23:12[/i] [KW41z] Wireless Alarm System Test Board (using KW41Z's Lierda module) is now available! Schematic diagramModule basePowerStorageIOLCD[b]...
damiaa NXP MCU
I want to use PIC16f1783 to realize serial communication, what is the problem with the following program? Please give me some advice, thank you very much
I want to use PIC16F1783 to realize the self-transmission and self-reception of the serial port, and use a 16M crystal oscillator as the external crystal oscillator. The program is as follows: #includ...
yyq12311 Microchip MCU
Looking forward to your suggestions: All things are difficult at the beginning [Embedded Amateur Group]
Everyone, take a look and hope to give more suggestions: https://home.eeworld.com.cn/my/space.php?uid=68517do=threadid=288 ###:)...
soso Embedded System
How to use single chip microcomputer to make electronic clock, how to achieve 10ppm correction by software
(10ppm error means 0.8 seconds error per day) If the error is found to reach 1 second per day when using a single-chip microcomputer as an electronic clock, how can the software be used to reduce this...
万里乌云 Embedded System
About the reading and writing problems of NAND FLASH K9F1208U0C
EP9315 CPU, previously used K9F1208U0B, read and write normally, after changing to K9F1208U0C, read and write can also be read and written, but always need to go through ECC check to correct the read ...
362912661 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1144  124  790  2392  2386  24  3  16  49  8 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号