EEWORLDEEWORLDEEWORLD

Part Number

Search

B1RHB-JC

Description
TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7
Categoryunclassified   
File Size256KB,8 Pages
ManufacturerOhmite
Websitehttps://www.ohmite.com
Download Datasheet Parametric View All

B1RHB-JC Overview

TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7

B1RHB-JC Parametric

Parameter NameAttribute value
Lead-freeYes
EU RoHS regulationsYes
stateACTIVE
terminal coatingGOLD OVER NICKEL
Manufacturer SeriesB
Switch typeTOGGLE SWITCH
Series B
Toggles
Process Sealed Subminiature Antistatic Toggles
A
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Rockers
Other Ratings
Programmable Illuminated PB
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Keylocks
Contact Timing:
Angle of Throw:
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum for locking lever models
50,000 operations minimum
Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)
Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)
Toggle L: 0.59N
Nonshorting (break-before-make)
26°
Materials & Finishes
Rotaries
Toggle:
Bushing:
Gasket:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Nickel plated brass
Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing
Nitrile butadiene rubber
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
Tactiles
Slides
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Touch
Installation
Mounting Torque:
.30 ~ .45Nm (2.65 ~ 3.98 lb
in) for A1 actuator with threaded bushing only
PCB Processing
Indicators
Soldering:
Cleaning:
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
Supplement
UL94V-0 available
The B Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A12
www.nkk.com
Is it necessary to add an emulator to stm32CAN communication reception?
After setting to normal mode, you must use the simulator to receive data correctly.After being offline, you can't receive the correct data when you power on directly. Why?Code:int main(void){#ifdef DE...
64331351 stm32/stm8
Altium Designer6.7 Registration File
Altium Designer6.7 Registration File...
jinpost PCB Design
Single pulse receiving component
The receiving component introduced in the abstract is an important part of the single pulse receiving system. This component contains three receiving channels. The microwave part adopts tube core devi...
JasonYoo Embedded System
2103 Undergraduate Group Topic
[i=s] This post was last edited by paulhyde on 2014-9-15 03:01 [/i] 2103 Undergraduate Group Topic...
qq374134697 Electronics Design Contest
Burn flash
[align=left][color=#000]Hello! [/color][/align][align=left][color=#000]I am using F28M36x chip, and I use CCS5.5 to burn M3 and C28 programs into flash. There is no error in the burning process, but a...
Yingzhe Microcontroller MCU
Why can't I jump out of the interrupt?
#include "stm32f10x.h"void GPIO_Configuration(void) {GPIO_InitTypeDef GPIO_InitStructure;/* Configure IO connected to LD1, LD2, LD3 and LD4 leds *********************/GPIO_InitStructure.GPIO_Pin = GPI...
极客王谦 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 184  1314  1578  223  721  4  27  32  5  15 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号