EEWORLDEEWORLDEEWORLD

Part Number

Search

B1SAB-GB

Description
TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7
Categoryunclassified   
File Size256KB,8 Pages
ManufacturerOhmite
Websitehttps://www.ohmite.com
Download Datasheet Parametric View All

B1SAB-GB Overview

TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7

B1SAB-GB Parametric

Parameter NameAttribute value
Lead-freeYes
EU RoHS regulationsYes
stateACTIVE
terminal coatingGOLD OVER NICKEL
Manufacturer SeriesB
Switch typeTOGGLE SWITCH
Series B
Toggles
Process Sealed Subminiature Antistatic Toggles
A
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Rockers
Other Ratings
Programmable Illuminated PB
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Keylocks
Contact Timing:
Angle of Throw:
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum for locking lever models
50,000 operations minimum
Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)
Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)
Toggle L: 0.59N
Nonshorting (break-before-make)
26°
Materials & Finishes
Rotaries
Toggle:
Bushing:
Gasket:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Nickel plated brass
Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing
Nitrile butadiene rubber
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
Tactiles
Slides
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Touch
Installation
Mounting Torque:
.30 ~ .45Nm (2.65 ~ 3.98 lb
in) for A1 actuator with threaded bushing only
PCB Processing
Indicators
Soldering:
Cleaning:
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
Supplement
UL94V-0 available
The B Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A12
www.nkk.com
PID experience summary
[i=s] This post was last edited by paulhyde on 2014-9-15 03:04 [/i] PID experience sharing...
bluelool1 Electronics Design Contest
Interview help
I submitted my resume at the job fair of the College Student Employment Center. I applied for a position in CNC system maintenance and testing. A CNC company notified me for an interview the next day....
宋佳佳 Talking about work
Looking for chip---Boost LED driver chip with 2 outputs and different output voltages
Specific requirements: DC-DCinput 5VLED boost chip (can also be used for buck, I made a boost circuit at the input end)Vout1 4 5-7V, Io1=100mA can be connected in series or in parallelVout2 4 3.0-3.3V...
sud0 LED Zone
How to implement GetSystemDirectory() in WINCE?
How to implement GetSystemDirectory() in WINCE? Is there any other function that can replace it? Can anyone give me some advice?...
pppphzmns Embedded System
About the problem of missing codes in wireless data transmission
When I use the 2.4GHz wireless transceiver chip nrf2e1 to transmit data, I find that there is only code leakage, no error code or repeated code. Can anyone give me some advice? Thank you! ~...
kangkang Embedded System
When compiling PB5.0, "ohcdmdd2.lib(cohcd.obj): fatal error LNK1000: Internal error durin" appears
As the title says, "ohcdmdd2.lib(cohcd.obj): fatal error LNK1000: Internal error during Pass2" appeared during compilation. The PB5,0 updates I installed are as follows: WinCEPB50-071231-Product-Updat...
yangjunweimail Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2835  701  947  784  2887  58  15  20  16  59 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号