EEWORLDEEWORLDEEWORLD

Part Number

Search

B22A1B-GF

Description
TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7
Categoryunclassified   
File Size256KB,8 Pages
ManufacturerOhmite
Websitehttps://www.ohmite.com
Download Datasheet Parametric View All

B22A1B-GF Overview

TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7

B22A1B-GF Parametric

Parameter NameAttribute value
Lead-freeYes
EU RoHS regulationsYes
stateACTIVE
terminal coatingGOLD OVER NICKEL
Manufacturer SeriesB
Switch typeTOGGLE SWITCH
Series B
Toggles
Process Sealed Subminiature Antistatic Toggles
A
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Rockers
Other Ratings
Programmable Illuminated PB
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Keylocks
Contact Timing:
Angle of Throw:
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum for locking lever models
50,000 operations minimum
Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)
Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)
Toggle L: 0.59N
Nonshorting (break-before-make)
26°
Materials & Finishes
Rotaries
Toggle:
Bushing:
Gasket:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Nickel plated brass
Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing
Nitrile butadiene rubber
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
Tactiles
Slides
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Touch
Installation
Mounting Torque:
.30 ~ .45Nm (2.65 ~ 3.98 lb
in) for A1 actuator with threaded bushing only
PCB Processing
Indicators
Soldering:
Cleaning:
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
Supplement
UL94V-0 available
The B Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A12
www.nkk.com
Digital Control Power Supply Based on TMS320F2806
[[i] This post was last edited by Jidongge on 2011-10-27 08:13[/i]]...
机动哥 DIY/Open Source Hardware
Reconfigurable Circuit Based on SRAM
The emergence of reconfigurable PLD (programmable logic device) based on SRAM has created conditions for system designers to dynamically change the logical functions of PLD in running circuits. PLD us...
alexa FPGA/CPLD
I need help from you guys. Super regenerative circuit reception problem
I am a beginner. Recently, I made a super-regenerative wireless receiving module according to the circuit diagram on the Internet, but I couldn’t receive any signal... I used an oscilloscope to measur...
qinsong RF/Wirelessly
[Help] MSP430 SPI receiving data error
Help: The SPI communication scheme between 430 microcontroller and TMS320VC5510 sets TMS320 as the host and 430 as the slave. TMS320 can correctly transmit the spi waveform, but the data received by 4...
wwj0102 Microcontroller MCU
How to choose the correct parameters for IGBT in inverter?
Assuming the rated power is 100KW, three-phase 380V * 1.414 is calculated as 500V, 2 IGBTs form a half bridge, and the duty cycle of a single IGBT is 0.4, the actual current is calculated to be approx...
eeleader Industrial Control Electronics
Application and quick selection guide of Texas Instruments high-performance analog devices in college students' electronic design
[i=s] This post was last edited by paulhyde on 2014-9-15 04:00 [/i] The two parts of Texas Instruments High-Performance Analog Devices in College Electronic Design and Quick Selection Guide need to be...
open82977352 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 913  1449  1760  1183  795  19  30  36  24  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号