EEWORLDEEWORLDEEWORLD

Part Number

Search

B25JB-JH

Description
TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7
Categoryunclassified   
File Size256KB,8 Pages
ManufacturerOhmite
Websitehttps://www.ohmite.com
Download Datasheet Parametric View All

B25JB-JH Overview

TOGGLE SWITCH,STRAIGHT,SPDT,ON-ON,PC TAIL TERMINAL,TOGGLE BAT,7

B25JB-JH Parametric

Parameter NameAttribute value
Lead-freeYes
EU RoHS regulationsYes
stateACTIVE
terminal coatingGOLD OVER NICKEL
Manufacturer SeriesB
Switch typeTOGGLE SWITCH
Series B
Toggles
Process Sealed Subminiature Antistatic Toggles
A
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Rockers
Other Ratings
Programmable Illuminated PB
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Keylocks
Contact Timing:
Angle of Throw:
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum for locking lever models
50,000 operations minimum
Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)
Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)
Toggle L: 0.59N
Nonshorting (break-before-make)
26°
Materials & Finishes
Rotaries
Toggle:
Bushing:
Gasket:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Nickel plated brass
Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing
Nitrile butadiene rubber
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
Tactiles
Slides
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Touch
Installation
Mounting Torque:
.30 ~ .45Nm (2.65 ~ 3.98 lb
in) for A1 actuator with threaded bushing only
PCB Processing
Indicators
Soldering:
Cleaning:
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
Supplement
UL94V-0 available
The B Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A12
www.nkk.com
Regarding the download line problem from laptop to FPGA development board, please advise!
[b][size=5][color=red]Please help me solve this problem: [/color][/size][/b] [b][size=5][color=red] Since my laptop does not have a parallel port, and the download cable given to me by my instructor i...
zqzq501311 FPGA/CPLD
The c file after converting the image using pnmtoc in the TI graphics library is too large, and the keil software is compiled successfully.
Recently, I encountered a problem when using TI's LM3S9B92 chip and the TI graphics library. I used the pnmtoc in the tool provided by the library to convert a pnm format image into a .c file. When I ...
zhoouauruheng Microcontroller MCU
Sci communication between pc and dsp
#if UART_INT==0 #if SCI while(ScibRegs.SCIFFRX.bit.RXFFST == 0); { } // wait for RRDY/RXFFST =1 for 1 data available in FIFO dataB = ScibRegs.SCIRXBUF.all; ScibRegs. SCITXBUF=dataB; f=dataB; while(Sci...
haha520525 DSP and ARM Processors
28035debug issue
[size=4]I would like to ask you experts, I am new to 28035, and the emulator is xds100v2. After configuring according to the tutorial, when debugging (Figure 1), the debug page (Figure 2) does not app...
herohxb Microcontroller MCU
Please help analyze the circuit, the 1500V surge test fails
Please see the attached picture, other functions are normal, but the 1500V surge test burns the switch tube (short circuit). Can you please analyze if there are any defects in the 2 varistors or other...
fireboct LED Zone
A long-standing problem: How to write a driver from the chip manual
This problem has troubled me for a long time. I have read a lot of chip manuals but cannot find the steps to write a driver. The chip manuals describe in detail the features supported by the chip, the...
yoyo1985914 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2250  475  1226  2758  1746  46  10  25  56  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号