EEWORLDEEWORLDEEWORLD

Part Number

Search

SH400M4R70APS11015

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 400V, 20% +Tol, 20% -Tol, 4.7uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size62KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SH400M4R70APS11015 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 400V, 20% +Tol, 20% -Tol, 4.7uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT

SH400M4R70APS11015 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompli
ECCN codeEAR99
capacitance4.7 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.0664 mA
Manufacturer's serial numberSH
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-25 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTR
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)400 V
ripple current57 mA
surface mountNO
Delta tangent0.2
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
Miniature Size Aluminum
Electrolytic Capacitors
SH
[ For General ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors
for the Rated Voltage up to 450V
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C / -25°~ +105°C
Working Voltage : 6.3 ~ 100V / 160 ~ 450V
Rate Capacitance Range : 0.1 ~ 15000µF / 0.1 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : 0.01CV +3 / 0.03CV+10
( Measurements shall be made after a2 minute charge at rated working voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
W V (V) : 6.3
10
16
25
35
50
63 ~ 100
160 ~ 250
350 ~ 450
D.F (%) : 26
22
18
16
14
12
10
15
20
For capacitor whose capacitance excceds 1000µF. The value of DF(%) is increased by 2% for every
addition of 1000µF.
W V (V)
:
6.3
4
8
10
3
6
16
2
4
25
2
3
35 ~ 100
2
3
160 ~ 250 350 ~ 450
4
8
4
8
DESCRIPTION
Long life for 2,000 hours at 105°C, ideally suited
for high quality and high reliability applications.
Feature High CV Product
Impedance : Z - 25°C / Z + 25°C
Z - 40°C / Z + 20°C
Load Life : 2000 Hours at 105°C Assured with Full Rated Maximum Ripple Current Applied
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
6.3~100V 100~470µF
6.3~100V 471~22000µF
160~450V ALL Cap(µF)
120
1.00
1.00
1.00
1.00
300
1.30
1.23
1.10
1.25
1K
1.57
1.34
1.13
1.40
10K~100K
2.00
1.50
1.15
1.60
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Temperature(°C)
Factor
65
1.70
85
1.40
105
1.00
Dimensions : mm
Rubber Stand-off
4.0
Rubber End Seal
DIAGRAM OF DIMENSIONS
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F 0.5
F 0.5
0.4Max.
15Min.
0.6
L
15Min.
5Min.
D 0.5
L
5Min.
D 0.5
7.5
10.0
0.8
0.8
Question: Circuit problem between LM3S6965 VDD and GND
1. Short all GND to ground, short all VDD25, then connect capacitor to ground; short all VDD33, then connect capacitor to ground. (US original circuit diagram) 2. Connect a capacitor between each VDD ...
leader Microcontroller MCU
I just learned assembly language and used RadASM2.2.1.8 for the first time. Why did the compilation fail? ?
I just learned assembly language. The following code is an example from the book. I used RadASM2.2.1.8 to compile it. 1. Source code DSEG SEGMENT MESS DB "MY NAME IS JACK",02H,0DH,0AH,"$" DSEG ENDS CS...
651061924 Embedded System
How to report a fault of optocoupler A316J
I would like to ask about the VCE saturation voltage drop protection and current protection of the A316J optocoupler. Are the output levels of the fault pins the same?...
sunboy25 Analog electronics
ESP32 Study Notes 2---WS2812 16*16 Dot Matrix
It has been a long time since my last post. I have been busy with work so I have slowed down my study progress. I will try to share my study status and experience in more detail in the future. I bough...
是最帅的啊 MicroPython Open Source section
[Play with ESP8266] Modify network parameters to solve reconnect problem
It seems that many forum members have encountered similar problems: after connecting ESP8266 to PC via mini USB cable, when opening the serial port tool, a sentence will pop up for no reason, and it k...
mikeliujia MicroPython Open Source section
ANC Active Noise Cancelling Headphones Solution
I recently won a prize of an ANC active noise reduction headset and I really want to understand the principle. I am out of date and can't keep up with the times. Does anyone have a data plan or schema...
yedaochang Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2068  1203  2279  1018  691  42  25  46  21  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号