EEWORLDEEWORLDEEWORLD

Part Number

Search

SX50M120A5F5815

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 50V, 20% +Tol, 20% -Tol, 120uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size69KB,4 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SX50M120A5F5815 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 50V, 20% +Tol, 20% -Tol, 120uF, Through Hole Mount, ROHS COMPLIANT

SX50M120A5F5815 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompli
ECCN codeEAR99
capacitance120 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
ESR170 mΩ
leakage current0.06 mA
Manufacturer's serial numberSX
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTAPE
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)50 V
ripple current670 mA
surface mountNO
Delta tangent0.08
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SX
[ For Low Impedance & Low E.S.R ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications
Miniature Size Aluminum
Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 100V
Rate Capacitance Range : 1 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.01 CV or 3(µA) Whichever is greater.
( Measurements shall be Made After a 2 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 6.3
10
16
25
35
50
63
80
100
D.F (%) : 19
16
14
12
10
8
8
7
7
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
Temperature Characteristics : at 120 Hz
WV (V)
:
Impedance : Z - 40°C / Z + 20°C
Case Dia
Load Life
øD
2000
3000
5000
Multiplier for Ripple Current
Frequency(Hz)
~4.4µF
5.6~33µF
34~330µF
331~1000µF
1200µF higher
50
0.30
0.40
0.60
0.65
0.85
120
0.40
0.50
0.70
0.90
0.90
300
0.50
0.60
0.80
0.90
0.95
1K
0.70
0.80
0.90
0.98
0.98
10K
0.80
0.90
0.95
1.00
1.00
100K
1.00
1.00
1.00
1.00
1.00
6.3
10
10
6
16
5
25
4
35
4
50
4
63
4
100
4
Used in switching regulator applications in com-
puters. Especially for high frequency.
Low impedance and E.S.R., high permissible ripple
current at high frequency and highter operation
temperature (-40°C to +105°C).
High Temperature Load Life at 105°C for 2000 ~
5000 Hours
DESCRIPTION
Load Life : At 105°C Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
DIAGRAM OF DIMENSIONS
4.0
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Temperature(°C)
Factor
65
1.80
85
1.50
105
1.00
Dimensions : mm
Vinyl Sleeve
(P.V.C)
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
Can someone please explain to me how the timer is calculated?
For example, the following code: void main(void) { WDTCTL = WDTPW + WDTHOLD; //Stop the watchdog timer P1DIR |= 0x01; //Set P1.0 as output //TA1CTL = RT1SSEL_0 + MC_2 + TAIE; //ACLK, timer A counting ...
wuyanyanke Microcontroller MCU
STM32 uart configuration
After configuring uart2, when sending data, there is no response and no waveform, but the corresponding uart1 has no problem....
说人不说见 Programming Basics
Model 2602 SourceMeter Instrument Performing LIV Test Sweep
Forward voltage test The forward voltage (VF) test verifies the forward DC characteristics of the laser diode. During the measurement, the current IF is swept and the voltage drop across the laser dio...
Jack_ma Test/Measurement
[Help] Newbie's help
If I make a circuit board according to this simulation diagram, can I just connect the power supply and measure the LED light? If I don't want it to light up immediately after powering on, how can I m...
1774315354 MCU
Touch screen controller
I am going to make a touch screen driver for a controller called TSC2006. What is the difference between it and ADS7846 controller? Can they be used interchangeably? If there is a difference, please d...
jlizheng Embedded System
【MicroPython】Using DS1820 single bus temperature sensor
[i=s]This post was last edited by dcexpert on 2016-4-13 22:41[/i] In the MicroPython source code, there is a single bus driver, which can easily drive single bus devices, such as reading the temperatu...
dcexpert MicroPython Open Source section

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1046  2320  2306  2138  1052  22  47  44  2  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号