EEWORLDEEWORLDEEWORLD

Part Number

Search

SX50M220APFL1019

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 50V, 20% +Tol, 20% -Tol, 220uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size69KB,4 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SX50M220APFL1019 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 50V, 20% +Tol, 20% -Tol, 220uF, Through Hole Mount, ROHS COMPLIANT

SX50M220APFL1019 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompli
ECCN codeEAR99
capacitance220 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
ESR110 mΩ
leakage current0.11 mA
Manufacturer's serial numberSX
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTAPE
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)50 V
ripple current1030 mA
surface mountNO
Delta tangent0.08
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SX
[ For Low Impedance & Low E.S.R ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications
Miniature Size Aluminum
Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 100V
Rate Capacitance Range : 1 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.01 CV or 3(µA) Whichever is greater.
( Measurements shall be Made After a 2 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 6.3
10
16
25
35
50
63
80
100
D.F (%) : 19
16
14
12
10
8
8
7
7
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
Temperature Characteristics : at 120 Hz
WV (V)
:
Impedance : Z - 40°C / Z + 20°C
Case Dia
Load Life
øD
2000
3000
5000
Multiplier for Ripple Current
Frequency(Hz)
~4.4µF
5.6~33µF
34~330µF
331~1000µF
1200µF higher
50
0.30
0.40
0.60
0.65
0.85
120
0.40
0.50
0.70
0.90
0.90
300
0.50
0.60
0.80
0.90
0.95
1K
0.70
0.80
0.90
0.98
0.98
10K
0.80
0.90
0.95
1.00
1.00
100K
1.00
1.00
1.00
1.00
1.00
6.3
10
10
6
16
5
25
4
35
4
50
4
63
4
100
4
Used in switching regulator applications in com-
puters. Especially for high frequency.
Low impedance and E.S.R., high permissible ripple
current at high frequency and highter operation
temperature (-40°C to +105°C).
High Temperature Load Life at 105°C for 2000 ~
5000 Hours
DESCRIPTION
Load Life : At 105°C Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
DIAGRAM OF DIMENSIONS
4.0
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Temperature(°C)
Factor
65
1.80
85
1.50
105
1.00
Dimensions : mm
Vinyl Sleeve
(P.V.C)
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
CodeWarrior warning C1420
CodeWarrior gives the following warning message during compilation: Warning: C1420: Result of function-call is ignored. Can anyone tell me what this means and how to solve it? The chip is MC9S08DZ60[[...
kwq498901 NXP MCU
C-SPY sucks, can't set breakpoints...
When setting breakpoints in C-SPY, I always get the error: Error[130]: "some breakpoint could not be set", no matter which statement I set it on, it can't be set.??? ??? ??? ??? ??? ??? ??? ??? ??? ??...
ladeng Microcontroller MCU
How does ulink2 power the board? How do I set it up?
[i=s] This post was last edited by paulhyde on 2014-9-15 03:48 [/i] How can I power the arm board with ulink2? How do I set it up? Does anyone know? Please help me...
hua19900322 Electronics Design Contest
Experiment on reading honeywell sensor using I2C of LM3S8962
Many of Honeywell's new generation of sensors have I2C output. I have two gas flow sensors on hand, so I want to test them on the EK-LM3S8962 development board.The program refers to Zhou Ligong's I2C ...
zoedigi Microcontroller MCU
It is difficult to find embedded software development talents with an annual salary of 100,000 yuan
On September 1, 2007, the "2007 China Software Industry Development and Enterprise Innovation Summit" held in Nanjing released information that in the first half of this year, the national software in...
maker Embedded System
Recruiting part-time matlab simulink training instructors
The corporate training company provides training for company employees and is looking for part-time matlab simulink teachers. The training is usually short-term, about three days, mainly on weekends. ...
nobody133 Recruitment

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1426  173  316  262  1008  29  4  7  6  21 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号