EEWORLDEEWORLDEEWORLD

Part Number

Search

SX80M15B5S8811

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 80V, 20% +Tol, 20% -Tol, 15uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size69KB,4 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SX80M15B5S8811 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 80V, 20% +Tol, 20% -Tol, 15uF, Through Hole Mount, ROHS COMPLIANT

SX80M15B5S8811 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompli
ECCN codeEAR99
capacitance15 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
ESR1100 mΩ
leakage current0.012 mA
Manufacturer's serial numberSX
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)80 V
ripple current138 mA
surface mountNO
Delta tangent0.07
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SX
[ For Low Impedance & Low E.S.R ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications
Miniature Size Aluminum
Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 100V
Rate Capacitance Range : 1 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.01 CV or 3(µA) Whichever is greater.
( Measurements shall be Made After a 2 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 6.3
10
16
25
35
50
63
80
100
D.F (%) : 19
16
14
12
10
8
8
7
7
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
Temperature Characteristics : at 120 Hz
WV (V)
:
Impedance : Z - 40°C / Z + 20°C
Case Dia
Load Life
øD
2000
3000
5000
Multiplier for Ripple Current
Frequency(Hz)
~4.4µF
5.6~33µF
34~330µF
331~1000µF
1200µF higher
50
0.30
0.40
0.60
0.65
0.85
120
0.40
0.50
0.70
0.90
0.90
300
0.50
0.60
0.80
0.90
0.95
1K
0.70
0.80
0.90
0.98
0.98
10K
0.80
0.90
0.95
1.00
1.00
100K
1.00
1.00
1.00
1.00
1.00
6.3
10
10
6
16
5
25
4
35
4
50
4
63
4
100
4
Used in switching regulator applications in com-
puters. Especially for high frequency.
Low impedance and E.S.R., high permissible ripple
current at high frequency and highter operation
temperature (-40°C to +105°C).
High Temperature Load Life at 105°C for 2000 ~
5000 Hours
DESCRIPTION
Load Life : At 105°C Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
DIAGRAM OF DIMENSIONS
4.0
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Temperature(°C)
Factor
65
1.80
85
1.50
105
1.00
Dimensions : mm
Vinyl Sleeve
(P.V.C)
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
How to realize switch alarm record in Kingview
I want to ask, how can I realize the switch alarm record in KingView? I want to record the information of M10.0 action? (M10.0 is an alarm symbol in my PLC). Is the alarm report of KingView for the hi...
eeleader-mcu Industrial Control Electronics
The network port of FriendlyArm's qq2440 development board is often blocked. Has anyone encountered this before?
When the power is just turned on, the data is sent and received normally, but after a while, it can no longer be received or sent. Then when I pinged the network port address, I found that it can be p...
cailingli521 Embedded System
WINCE ENABLE/DISABLE WIFI
Hello everyone! I would like to ask if you have done similar projects on wince. Our current requirements are as follows: The application uses standard API to set the WIFI switch and power status. Plea...
slf1986 Embedded System
In I2C communication, sometimes the host cannot receive the ACK response from the slave, and the SDA line will be pulled dead (low level). Can you give me some advice?
In I2C communication, sometimes the host cannot receive the ACK response from the slave, and the SDA line will be pulled dead (low level). Can you give me some advice?...
xingwang Embedded System
PCB Basic Learning Series: PADS2005 to Gerber File
PCB Basic Learning Series: PADS2005 to Gerber File Tutorial, welcome to download, learn and communicate! (Click on the attachment to download)...
jlcgwc PCB Design
About ISD1110
I use S52's P2.0~P2.2 to connect ISD1110's REC, PLAYE, PLAYL. Why do I output 1 to all three ports, but the multimeter always outputs 0! I added a pull-up resistor, but the problem still exists! After...
woshijingshui Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 113  701  2469  1192  814  3  15  50  24  17 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号