LCS052T28WA28CC datasheet, PDF

Datasheet> All Categories > Mechanical and electronic products> switch> LCS052T28WA28CC

LCS052T28WA28CC: DescriptionSNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 12.2mm, PANEL MOUNT, ROHS COMPLIANT; CategoryMechanical and electronic products switch; File Size229KB，4 Pages; ManufacturerC&K; Environmental Compliance

Download Datasheet Parametric View All

LCS052T28WA28CC Overview

SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 12.2mm, PANEL MOUNT, ROHS COMPLIANT

LCS052T28WA28CC Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	C&K
package instruction	ROHS COMPLIANT
Reach Compliance Code	compli
ECCN code	EAR99
Actuator stroke	12.2 mm
Actuator type	LEVER
body width	6.4 mm
body height	15.95 mm
Body length or diameter	19.8 mm
Contact (AC) maximum rated R load	6A@250VAC
Maximum contact current (AC)	6 A
Maximum contact voltage (AC)	250 V
Electrical life	10000 Cycle(s)
Manufacturer's serial number	LCS
Installation features	PANEL MOUNT
Maximum operating force	1.99 N
Maximum operating temperature	125 °C
Minimum operating temperature	-40 °C
Maximum pre-travel	10.1 mm
seal	IP67
surface mount	NO
Switch action	MOMENTARY
switch function	SPDT
Switch type	SNAP ACTING/LIMIT SWITCH
Termination type	WIRE

Preview

Download Datasheet

View All

LCS Series

Subminiature Sealed Snap-acting Switches

Features/Benefits

•

Compact design

•

Long life and high electrical capacity

•

Quick connect, solder terminals,

PC terminals, wire leads

•

Wide variety of actuator styles

•

RoHS compatible, RoHS compliant

•

IP67

Specifications

CONTACT RATING: 6 AMP, 125/250 V AC

and

5 AMP, 125/250 V AC

0.1 AMP, 125/250 V AC

ELECTRICAL LIFE: 10,000 cycles

INSULATION RESISTANCE: 100 M ohm min.

DIELECTRIC STRENGTH: 1,000 VAC

OPERATING TEMPERATURE: –40ºC to +125ºC without wire

–40ºC to +85ºC with wires

OPERATING FORCE: (see ACTUATOR’S option sections).

MOUNTING: 2-56 screws, torque 2.3 in/lbs max.

NOTE:

Specifications and materials listed above are for switches with standard options.

For information on specific and custom switches, consult Customer Service center.

Typical Applications

•

Motorized equipment

•

Sump pump

•

Thermostatic controls

•

Computers

•

Air conditioners

Models Available

Materials

SWITCH HOUSING: Thermoplastic polyester or high temperature

thermoplastic (PTS) (UL 94V-0).

ACTUATOR BUTTON: Thermoplastic polyester.

SPRING: Copper alloy.

PIVOT: Copper alloy.

MOVABLE CONTACTS: Silver nickel

STATIONARY CONTACTS: Silver nickel on copper alloy.

TERMINALS: Copper alloy.

ACTUATOR LEVEL: Stainless steel.

Snap-acting

Build-A-Switch

To order, simply select desired option from each category and place in the appropriate box. Available options are shown and

described on pages J-27 thru J-29. For additional options not shown in catalog, consult Customer Service Center.

Series

LCS

Contact Rating

5 AMP, 125/250 V AC

6 AMP, 125/250 V AC

0.1 AMP, 125/250 V AC

Operating Force

150 grams

203 grams

Actuator

P00

Pin plunger

T00

0.45 mm short lever

T05

5.05 mm short lever

T07

7.05 mm short lever

T13

13.15 mm lever

T19

20.95 mm lever

T28

28.35 mm lever

T43

43.55 mm lever

S26

6.25 mm simulated lever

A05

4.85 mm lever roller

Circuitry

SPDT

SPST N.C.

SPST N.O.

Wire Type AWG

20 AWG

22 AWG

24 AWG

26 AWG

28 AWG

30 AWG

Wire UL #

(when required)

UL1007

UL1015

UL1430

UL1061

UL1330

Terminations

Solder

0.110 Quick Connect

PC Thru Hole

Wire leads potted

Wire leads non-potted

Wire Side (when required)

Wire out the bottom

Wire out the right side

Wire out the left side

None

Dimensions are shown: mm

Specifications and dimensions subject to change

J–26

www.ck-components.com

Recommended Resources

Gas automatic detection alarm circuit

20V, 500mA regulated power supply circuit

Novel high-power multi-function power amplifier module 03

Use NE555 to make automatic telephone lighting

Flashing alarm circuit 03

Internal structure of UC3906

Capacitor step-down power supply principle and calculation formula: This type of circuit is usually used to obtain a low-cost non-isolated low-current power supply. Its output voltage can usually range from a few volts to more than 30 volts, depending on the Zener vol...; linda_xia Analog electronics

【Design Tools】Supplemental Device Guide for Monitoring Devices for Xilinx FPGAs: Advanced manufacturing techniques and smaller process geometries drive the core voltage to lower levels. This trend, combined with existing I/O standards, has led to the design of multiple voltage rai...; GONGHCU FPGA/CPLD

There's a new theory at hand that could make convolution computations more efficient: My tutor has a new theory that can improve the efficiency of convolution calculations, mainly in terms of speed and accuracy. It is better than the traditional convolution using FFT, but the applicabl...; Awakeningroom Embedded System

8051 Single Chip Microcomputer Practice and Application: Upload a classic 51 development book!...; wurongyan 51mcu

Issues on floating-point calculations on fixed-point DSP: When using fixed-point DSP for floating-point calculations, Q value calibration is used. How does DSP implement Q value? For example, in the following program,let x = 3.0, y = 3.1, then the floating-p...; weiaa1911 DSP and ARM Processors

Let's take a look: [i=s] This post was last edited by Mengxin on 2019-2-18 13:59 [/i] K60's question: Why does Putty not respond to the serial port printing characters? (I have checked many times that the interface numb...; 萌新本体 ARM Technology

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components