EEWORLDEEWORLDEEWORLD

Part Number

Search

CH1817-L

Description
Family of Low Profile DAA Modules
File Size295KB,7 Pages
ManufacturerETC1
Download Datasheet View All

CH1817-L Overview

Family of Low Profile DAA Modules

CH1817
Family of Low Profile DAA Modules
INTRODUCTION
The CH1817 is a Family of Low Profile Data Access
Arrangement (DAA) Modules. They are compatible
with all modem chip sets. These devices have been
tested to meet or exceed FCC Part 68 requirements
and are Canadian DOC approvable. They are also
recognized by Underwriters Laboratories to UL 1459
Specifications.
The CH1817 modules are ultra small (1.0” x 1.0”
x0.35”) affording an easy integration into space-
sensitive designs, including laptop and hand-held
computer based products. The CH1817 family of
products may be socketed or mounted directly onto a
Printed Circuit Board (PCB). The telephone line
connection is made through TIP and RING to an RJ-11
jack or equivalent.
The CH1817 is intended for use with FAX/modem chip
sets that have a data throughput of up through
V.32bis. For High Speed Applications, Cermetek
recommends the CH1837A.
FEATURES
Low Profile, Ultra small size: 1.0” x 1.0” x 0.35”
Complete DAA function
Ring detection
Built-in 2-wire to 4-wire conversion
Lightweight
Multimedia compatible
+5V operation
1000 VAC isolation
800 Volt surge protection
V.32bis/14,400bps, applications
UL1459 recognized
CH1817-L: Low power consumption and Common
mode noise rejection filter
CH1817-LM (special order): Reduced transmit
attenuation
CH1817-D: Differential transmission input and 0dB
transmission insertion loss.
FUNCTIONAL DESCRIPTION
Ring Detection.
Referring to the block diagram in
Figure 1, incoming ring detection is performed by the
CH1817 and the RI pin is set Low during the 2 second
(typical) ring period and is restored to High for the 4
seconds (typical) between rings. During incoming ring
signal activity, the RI output is pulsed at the same
frequency as the ringing signal, typically 20Hz. Figure
2 contains additional external circuitry which may be
used to provide an envelope indication of the ring
signal. The internal ring detection circuit is designed
to deter false indications due to pulse dialing or noise
on the line.
The RI output of the CH1817 is diode protected.
Therefore, an external pull-up resistor (R>100Kohm)
to +5V may be utilized to activate the ring detection
circuit when the CH1817 is not connected to power.
This can be handy in designs where power
consumption is of concern. When circuited in this
manner, there is virtually no current draw until a ring
signal is present.
RI
Output: Active low
Opto coupler, 30KΩ pull-up
Square wave: 15-68Hz (Typ. 20Hz)
Sensitivity: 38Vrms across Tip & Ring
XMIT
RCV
RI
OFFHK
V
CC
GND
ISOLATION
SURGE
AND
PROTECTION
CIRCUITRY
TIP
RING
HYBRID
2W/4W
CONVERTER
OFF-HOOK
SWITCH
RING DET.
Figure 1. CH1817 DAA Functional Block Diagram.
2002
Cermetek Microelectronics, Inc.
Page 1
Document No. 607-0007 Revision B (01/02)
TI Bluetooth Low Energy (BLE) training videos
Bluetooth activities are hot in the forum, here are some video links [url=http://focus.ti.com/cn/general/docs/video/Portal.tsp?entryid=0_s1hxlvhy&lang=cn]BLE course (I): Bluetooth low energy technolog...
fish001 RF/Wirelessly
Alternative interpretation of MCU (happy for a while)
Seeing so many people replying to the topic "Girls' Single Chip Computer" in the forum, I suddenly thought about what MCU is and why boys like it so much? MCU is a combination of (MM Computer unite) M...
kakashi2010 Embedded System
Should I manage the money myself or give it to my significant other?
[i=s]This post was last edited by gh131413 on 2014-9-25 10:32[/i] In this era of high divorce rates, do you manage your own personal savings or do you give it to your significant other?...
gh131413 Talking
IAR MSP430 compilation error description
IAR MSP430 compilation error description[b] Download: [url=https://download.eeworld.com.cn/download/qwqwqw2088/544506] IAR MSP430 compilation error description [/url] [/b]...
qwqwqw2088 Microcontroller MCU
How to use Windows CE under XP
I want to use evc4.0 tools for development. Can I use it directly after installing it under XP?...
zy7786879 Embedded System
Problems with STM32SPI after Keil compilation and optimization
Hello everyone, I am using Keil UV4 MDK4.0 compiler. When using STM32's SPI interface to communicate with CC2420, I found that when the program is not optimized (LEVEL 0), MISO can receive information...
k.n.521 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 691  10  1513  2836  2853  14  1  31  58  21 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号