(max) defines a read cycle. Read access time is measured
from the latter of Chip Enable, Output Enable, or valid address
to valid data output.
SRAM Read Cycle 1, the Address Access in figure 4a, is
initiated by a change in address inputs while any chip are enabled
with G asserted and Wn deasserted. Valid data appears on data
outputs DQ(7:0) after the specified t
AVQV
is satisfied. Outputs
remain active throughout the entire cycle. As long as Chip
Enable and Output Enable are active, the address inputs may
change at a rate equal to the minimum read cycle time (t
AVAV
).
SRAM read Cycle 2, the Chip Enable - Controlled Access in
figure 4b, is initiated by En going active while G remains
asserted, Wn remains deasserted, and the addresses remain
stable for the entire cycle. After the specified t
ETQV
is satisfied,
the eight-bit word addressed by A(18:0) is accessed and appears
at the data outputs DQ(7:0).
SRAM read Cycle 3, the Output Enable - Controlled Access in
figure 4c, is initiated by G going active while En is asserted, Wn
is deasserted, and the addresses are stable. Read access time is
t
GLQV
unless t
AVQV
or t
ETQV
have not been satisfied.
2
WRITE CYCLE
A combination of Wn less than V
IL
(max) and En less than
V
IL
(max) defines a write cycle. The state of G is a “don’t care”
for a write cycle. The outputs are placed in the high-impedance
state when either G is greater than V
IH
(min), or when Wn is less
than V
IL
(max).
Write Cycle 1, the Write Enable-controlled Access in Figure 5a,
is defined by a write terminated by Wn going high, with En still
active. The write pulse width is defined by t
WLWH
when the write
is initiated by Wn, and by t
ETWH
when the write is initiated by
En. Unless the outputs have been previously placed in the high-
impedance state by G, the user must wait t
WLQZ
before applying
data to the nine bidirectional pins DQ(7:0) to avoid bus
contention.
Write Cycle 2, the Chip Enable-controlled Access in Figure 5b,
is defined by a write terminated by the latter of En going inactive.
The write pulse width is defined by t
WLEF
when the write is
initiated by Wn, and by t
ETEF
when the write is initiated by the
En going active. For the Wn initiated write, unless the outputs
have been previously placed in the high-impedance state by G,
the user must wait t
WLQZ
before applying data to the eight
bidirectional pins DQ(7:0) to avoid bus contention.
TYPICAL RADIATION HARDNESS
The UT8Q512K32E SRAM incorporates features which allows
operation in a limited radiation environment.
Table 2. Radiation Hardness
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
50
<1.1E-9
krad(Si)
Errors/Bit-Day
Notes:
1. The SRAM will not latchup during radiation exposure under recommended
operating conditions.
2. 90% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum.
3
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
DC input current
LIMITS
-0.5 to 7.0V
-0.5 to 7.0V
-65 to +150C
1.0W (per byte)
+150C
10C/W
±
10 mA
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175C during burn-in and steady-static life.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
LIMITS
3.0 to 3.6V
(W) Screen - 40C to 105C
0V to V
DD
4
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
-40C to +105C (V
DD
= 3.3V + 0.3V)
SYMBOL
V
IH
V
IL
V
OL1
V
OL2
V
OH1
V
OH2
C
IN1
C
IO1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
Low-level output voltage
High-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
(TTL)
(TTL)
I
OL
= 6mA, V
DD
= 3.0V (TTL)
I
OL
= 200A,V
DD
= 3.0V (CMOS)
I
OH
= -4mA,V
DD
= 3.0V (TTL)
I
OH
= 200A,V
DD
= 3.0V (CMOS)
= 1MHz @ 0V
= 1MHz @ 0V
V
IN
= V
DD
and V
SS,
V
DD
= V
DD
(max)
-2
-2
2.4
V
DD
-.010
45
25
2
2
CONDITION
MIN
2.0
0.8
0.4
0.08
MAX
UNIT
V
V
V
V
V
V
pF
pF
A
A
Three-state output leakage current V
O
= V
DD
and V
SS
V
DD
= V
DD
(max)
G = V
DD
(max)
Short-circuit output current
V
DD
= V
DD
(max), V
O
= V
DD
V
DD
= V
DD
(max), V
O
= 0V
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
Inputs: V
IL
= V
SS
I
OUT
= 0mA
E1 = V
DD
- 0.5, V
DD
=
V
DD
(max)
V
IH
= V
DD
- 0.5V
-40C &
25C
105C
I
OS2, 3
I
DD
(OP)
-90
90
mA
Supply current operating
@ 1MHz
(per byte)
40
mA
I
DD1
(OP)
Supply current operating
@40MHz
(per byte)
70
mA
I
DD2
(SB)
4
Supply current standby
@0MHz
(per byte)
9
24
mA
mA
Notes:
* Post-radiation performance guaranteed at 25C per MIL-STD-883 Method 1019.
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
4. Post-radiation limit based off of high temperature limit.
[font=Courier]At the beginning of 2008, the automotive electronics industry reviewed the development of 2007 and raised some thought-provoking questions. Local automotive electronics companies will fa...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:08[/i] I looked at the component list for 2003 and there was a high-frequency varactor diode, and the topic for that year was a voltage-contr...
For a single-port circuit without independent source, which has two lead-out terminals, has no independent power supply inside and the current on the two terminals is the same, it is called a single-p...
2021 is a new start. This year, the electronics industry faces new challenges, both in terms of physical and economic aspects.
In general, more consumption and boosting the economy can better serve th...
Project requirements:Develop a redundant disk array card with 4 SATA hard disks based on Xilinx Kintex7 325T, and communicate with the PC through the PCIe 2.0 X8 interface. See the attachedSATA3.0 int...
PV DC fuses are safety devices used to protect PV panels, inverters, and DC loads. To ensure their safety and reliability, they must be UL248 certified.
Before applying for UL248 certifi...[Details]
Electric vehicles are currently gaining momentum, but this is just a facade. Fuel-powered vehicles remain unchallenged. While electric vehicles boast unique advantages in environmental emissions an...[Details]
With the rapid advancement of automation technology, collaboration between robots is no longer just science fiction. Imagine dozens of machines moving goods in a warehouse without interfering with ...[Details]
On August 21, WeRide officially launched WePilot AiDrive, a one-stage end-to-end assisted driving solution developed in cooperation with Bosch. This comes only half a year after the two parties' "t...[Details]
In daily life, power transformers have different functions and uses due to different usage scenarios. The most common ones can be divided into: control transformers, isolation transformers, rectifi...[Details]
On August 22, the Wall Street Journal reported on the 21st local time that the new US government does not plan to acquire equity in semiconductor wafer foundry giant TSMC and Micron, one of the thr...[Details]
In this final installment of a five-part blog series, I will discuss noise in op amps driving headphone loads and some techniques for reducing it. Previous posts have discussed headphone load power...[Details]
The intelligent
dust monitoring system intelligently monitors dust concentrations at and around construction sites. All concentration values are transmitted to a cloud server for
cloud co...[Details]
The primary control objective in this case is the display and alarming of data parameters on the Xinheng control scale instrument. The system's main PLC uses a Siemens CPU, and data is collected vi...[Details]
Recently, UBTECH announced its patent for "robot self-battery replacement structure, device and method".
The Qichacha patent abstract shows that the robot's self-battery replacement stru...[Details]
As in-vehicle audio and video entertainment features become increasingly diverse, the demand for digital transmission of audio and video information is urgent. Traditional protocols such as IEEE 13...[Details]
Vision is the most sensitive and direct way for humans to perceive things. It allows us to acquire a wealth of information about our surroundings without physical contact. However, due to the compl...[Details]
PLC is the foundation of modern industry. Although it is a product of the Second Industrial Revolution, it has experienced nearly a century of ups and downs. Not only has it not disappeared, but it...[Details]
New energy electric vehicles are energy-saving, environmentally friendly, have low operating costs, and enjoy strong support from national policies. With the growth in sales of new energy electric ...[Details]
Compared to gasoline-powered vehicles, electric vehicles have a simpler structure, allowing for greater flexibility in the layout of various components. While electric and gasoline-powered vehicles...[Details]
Automotive Electronics
京公网安备 11010802033920号
EEWORLD
