EEWORLDEEWORLDEEWORLD

Part Number

Search

306E-306-3002

Description
Board Connector, 6 Contact(s), 1 Row(s), Male, Straight, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle
CategoryThe connector    The connector   
File Size153KB,1 Pages
ManufacturerMethode Electronics Inc.
Download Datasheet Parametric View All

306E-306-3002 Overview

Board Connector, 6 Contact(s), 1 Row(s), Male, Straight, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle

306E-306-3002 Parametric

Parameter NameAttribute value
MakerMethode Electronics Inc.
Reach Compliance Codeunknow
ECCN codeEAR99
Other featuresWITH HOOKS & LOCKING RAMP
Board mount optionsPCB EDGE LOCKING HOOK
subject depth0.45 inch
body length0.93 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN-PB ON NI
Contact completed and terminatedTIN/LEAD OVER NICKEL
Contact point genderFEMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact resistance5 mΩ
Contact styleSQ PIN-SKT
DIN complianceNO
Dielectric withstand voltage1500VAC V
Filter functionNO
IEC complianceNO
maximum insertion forceLIF N
Insulation resistance500000000000 Ω
Insulator colorNATURAL
insulator materialNYLON
MIL complianceNO
Plug contact pitch0.156 inch
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
OptionsGENERAL PURPOSE
PCB contact patternRECTANGULAR
polarization keyPOLARIZED HOUSING
Rated current (signal)7 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.165 inch
Terminal pitch3.96 mm
Termination typeSOLDER
Total number of contacts6
UL Flammability Code94V-0
Evacuation force-minimum valueLIF N
.156” (3.96mm)
Through Hole Vertical Mount Connector
3000 SERIES “TERMACON”
PART NUMBER LEGEND
30XX-XXX-XXXX
CONTACT TAIL DIMS (SEE TABLE 2)
CONTACT MATERIAL (SEE NOTE 1)
OPTIONS
2 - HIGH INSERTION FORCE CONTACT
3 - LOW INSERTION FORCE CONTACT
NO. OF POSITONS (SEE TABLE 1)
OPTIONS
0-
1-
3-
6-
7-
8-
WITH LEGS
WITH HOOKS
WITH HOOKS AND LOCKING RAMP
WITH LOCKING RAMP
WITH HOOKS, LOCKING RAMP AND POLARIZING KEY
WITHOUT HOOKS, W/ LOCKING RAMP AND POLARIZING KEY
CONTACT FINISH (SEE NOTE 2)
INSULATOR MATERIAL (SEE NOTE 1)
MATING HEADERS: 3100 SERIES
HOLE
LEG
LOCKING
RAMP
POLARIZING KEY &
LOCKING RAMP
Connector Products
1700 Hicks Road • Rolling Meadows, IL 60008 USA
Telephone: 847.392.3500 • Fax: 847.392.9404
email: mcpsales@methode.com • Web Page: www.methode.com
TI dsp28335 routine pwm explanation
DSP28335 has 12 16-bit ePWMs, which can control frequency and duty cycle. The clock of ePWM TBCLK = SYSCLKOUT / (HSPCLKDIV × CLKDIV):The PWM signal frequency is determined by the time base period regi...
Aguilera DSP and ARM Processors
AVR MCU uses timer counter to extend external interrupt
The external interrupt is occupied by other applications. I want to use the falling edge to trigger. When the timer counts the external pulse, should it detect the falling edge or the rising edge?...
加油费 Microchip MCU
Mobile power USB load detection circuit principle
In the mobile power USB load automatic detection circuit, the B pole of the transistor is connected to the GND pin of the USB interface, and the C pole is connected to the MCU IO pin. When the USB cha...
bink2015 Power technology
Recommended Classic Materials on Software Testing (Thirteen) --- Effective Software Testing
[align=center][size=5][font=宋体]Recommendation of Classic Materials on Software Testing (Thirteen)[/font][font=Times New Roman]---[/font][/size][font=Helvetica, Tahoma, Arial, sans-serif][size=5][color...
tiankai001 Download Centre
I would like to ask an expert, what should I do if the board density is high and the DRV8825 driver motor makes a loud noise?
I have made two new boards. Since they are still in the experimental stage, I am eager to put them into production. So many problems have been exposed, especially the problem of loud motor noise. What...
shenlan0302 TI Technology Forum
Why is there such asymmetry regarding the gain specification?
[size=3][color=#000000][font=Verdana] Some engineers often ask during the design process, "Why are the specified minimum and maximum gain errors of [/font][font=Verdana]ADCs so different?" This articl...
fish001 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2332  291  1168  2051  782  47  6  24  42  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号