EEWORLDEEWORLDEEWORLD

Part Number

Search

VFOV200-WADCH-10

Description
HCMOS/TTL Output Clock Oscillator, 5MHz Nom, ROHS COMPLIANT, HERMETIC SEALED PACKAGE-5
CategoryPassive components    oscillator   
File Size435KB,4 Pages
ManufacturerCTS [CTS Corporation]
Environmental Compliance  
Download Datasheet Parametric View All

VFOV200-WADCH-10 Overview

HCMOS/TTL Output Clock Oscillator, 5MHz Nom, ROHS COMPLIANT, HERMETIC SEALED PACKAGE-5

VFOV200-WADCH-10 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerCTS [CTS Corporation]
Reach Compliance Codeunknow
Ageing0.1 PPM/YEAR
Maximum control voltage4.3 V
Minimum control voltage
Frequency Adjustment - MechanicalNO
frequency stability0.005%
Frequency Stability - Voltage0.001 ppm
input power1.2 W
Manufacturer's serial numberVFOV200
Installation featuresSURFACE MOUNT
Nominal operating frequency5 MHz
Maximum operating temperature50 °C
Minimum operating temperature
Oscillator typeHCMOS/TTL
Output load10 KOHM, 15 pF
Oven power supply voltage5V
physical size25.4mm x 22.1mm x 13.2mm
Maximum supply voltage5.25 V
Minimum supply voltage4.75 V
Nominal supply voltage5 V
surface mountYES
Preheating power3.5 W
Maximum warm-up time3 Minute
VFOV200
OCXO – High Frequency, High Stability
HCMOS / SINE WAVE
Features
5MHz to 250MHz frequency range
High stability (up to 5ppb over -40°C to +85°C)
HCMOS or sine wave output
RoHS Status
Applications
PLL Reference for Telecommunication Systems
Stratum 3E Clock Systems
Base Station Reference Source
GPS Holdover
Instrumentation / Test and Measurement
Electrical Specifications
Parameter
Frequency
Range
Symbol
F
Vs. Operating temperature
G: -40C to +85C
Vs. Supply Voltage
Vs. Aging / Day
Vs. Aging / Year
Operating
Temperature
Range
Allan Variance
SSB Phase
Noise
Retrace
G-sensitivity
Supply Voltage
Power
Consumption
Warm-Up Time
Vcc
P
τ
steady state, 25C
steady state, -30C
start-up
to 0.1ppm accuracy
T
1s
10Hz
100Hz
1kHz
10kHz
100kHz
After 30 min.
worst direction
11.4
4.75
3.15
12.0
5.0
3.3
1.0
2.0
3.2
2
-30
10e-12
-125
-143
-150
-158
-160
20
1
12.6
5.25
3.45
1.2
2.2
3.5
3
Condition
Min
5
5
±1
0.5
0.1
+70
Typ
Max
250
Unit
MHz
ppb
ppb
ppb
ppm
C
STD option shown.
See “How to Order”
Chart below
Ref. Vcc typ.
after 30 days
0.2ppb available
STD option shown.
See “How to Order”
Chart below
For 10MHz oscillator
dBc/Hz
(For 100MHz see plot
next page)
Note
Frequency
Stability
∆F/F
ppb
ppb/g
V
W
min
75 South Street, Hopkinton, MA 01748 • 800-982-5737 • 508-435-6831 • FAX 508-497-6377 • www.ctsvalpey.com • RevG0413
Specifications are subject to change without notice
1
Can the interrupt flag of the CAN chip be reset by itself?
MCP2515 is a CAN bus chip. When receiving a message, if the CANINTE receive bit is enabled, the CANINTF receive bit is set to 1 and an interrupt is generated. Theoretically, after the MCU detects the ...
pikky Embedded System
vxworks NAT question. I will give points to all replies. If you don't have enough points, I will add more.
Dear experts on the forum, has anyone done NAT stuff under vxworks5.4? Can you give me some tips? This thing has tortured me to death. You can also send the information to my email: zhouxiongjun@hotma...
merryimage Real-time operating system RTOS
Can LPC1114 store data on-chip during power-off?
The datasheet shows that there is no on-chip EEPROM. Is it possible to store data in it? Or is there another way to do it?...
shoooter NXP MCU
Philips launches the latest ultra-thin and stylish GPS car navigator
With the rapid development of science and technology, self-guided travel has gradually become a fashion, and equipping your car with an excellent GPS satellite navigation product has become a daily ne...
frozenviolet Automotive Electronics
Why can I enter an interrupt without calling GPIO_EXTILineConfig?
I just started learning STM32 and now I have encountered a problem and I don’t understand why. I wrote a simple interrupt program according to the tutorial, which is to press the button and then enter...
lys520gc stm32/stm8
spi,cs,if I don't use it,can I use it as an io port
For example, if I only use the three lines of SPI, clk, miso, and mosi, can my cs pin be used as a separate io port?...
乱起东城 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 773  1512  2056  2061  852  16  31  42  18  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号