MMC-14-A-9505-3-E-2-B-1 datasheet, PDF

Datasheet> All Categories > Wireless rf/communication> Optical fiber> MMC-14-A-9505-3-E-2-B-1

MMC-14-A-9505-3-E-2-B-1: DescriptionSplitter/Coupler, 1X4 Port, 95/5 Ratio, FC/PC Connector; CategoryWireless rf/communication Optical fiber; File Size215KB，1 Pages; ManufacturerLightel Technologies Inc.

Download Datasheet Parametric View All

MMC-14-A-9505-3-E-2-B-1 Overview

Splitter/Coupler, 1X4 Port, 95/5 Ratio, FC/PC Connector

MMC-14-A-9505-3-E-2-B-1 Parametric

Parameter Name	Attribute value
Maker	Lightel Technologies Inc.
Reach Compliance Code	unknow
Connection Type	FC/PC CONNECTOR
Fiber optic equipment types	SPLITTER/COUPLER
Fiber type	100/140
Maximum insertion loss	7.5 dB
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Nominal operating wavelength	1310 nm
Port configuration	1X4
Split ratio/coupling ratio	95/5

Preview

Download Datasheet

View All

FBT COUPLER

Multimode Coupler

(Based on 50/50)

Parameter

Central Wavelength

Configuration

Insertion Loss*

50/125 Fiber

62.5/125, 100/140, 105/125 Fiber

Directivity

TDL

Operating & Storage Temperature

Light Duty ( B )

Package Dimensions

Medium Duty ( L )

(dimensions in mm)

Heavy Duty ( K, R )

1x2, 2x2

≤ 4.9 dB

≤ 4.6 dB

630, 850, 980, 1060, 1310, 1550nm

1x3

1x4

1x8

1x16

≤ 6.7 dB

≤ 7.8 dB

≤ 11.5 dB

≤ 15 dB

≤ 6.4 dB

≤ 7.5 dB

≤ 11 dB

≤ 14.2 dB

≥ 40 dB

≤ 0.2 dB

- 40° C ~ + 85° C

3.0(

) x55.0(L)

3.0(

)x60.0(L)

100 x 12 x 8

3.0(

) x60.0(L) 3.0(

) x 60.0(L) 3.0(

) x 60.0(L)

100 x 12 x 8

95 X 75 X 6

100 x 12 x 8

95 X 75 X 6

100 x 12 x 8

130 X 100 X 6

5.0(

) x 60.0(L)

135 x 100 x 10

130 X 100 X 8.5

Tap Couplers

Maximum Insertion Loss

Coupling

Ratio

60/40

70/30

80/20

90/10

95/5

99/1

50/125 µm

4.5/6.5 dB

3.9/8.0 dB

3.2/10.0 dB

2.7/13.5 dB

2.4/17.0 dB

1.4/22.0 dB

62.5/125 µm

3.6/5.8 dB

3.0/7.0 dB

2.4/9.0 dB

1.9/12.5 dB

1.5/16.5 dB

1.1/22.0 dB

100/140 µm &

105/125 µm

3.0/5.0 dB

2.3/6.3 dB

1.7/8.3 dB

1.2/12.0 dB

1.0/16.0 dB

0.8/22.0 dB

* All data tested under LED direct launching conditions.

Note1: All values specified are without connectors.

Note2: Higher performance specifications available upon request.

M M C-

-A-

Port Number A Grade

12: 1 x 2

22: 2 x 2

13: 1 x 3

14: 1 x 4

18: 1 x 8

116: 1 x 16

Wavelength

A: 630 nm

B: 850 nm

C: 1060 nm

D: 980 nm

E: 1310 nm

H: 1550 nm

Connector

0: None

1: FC/PC

3: SC/ PC

9: Special

C: ST

Coupling Ratio

Fiber Type

xy % : xy %

1: 50/125 µm

EVEN: even split 2: 62.5/125 µm

3: 100/140 µm

4: Special

5: 105/125 µm, NA=0.15

6: 105/125 µm, NA=0.22

Fiber Length

Pigtail Style

1: 1 meter

(=Package style)

2: 2 meter

B: bare fiber

S: Special

L: 900 µm loose tube

K: 2mm cable

R: 3mm cable

www.lighteltech.com

2210 Lind Ave SW, Suite 100

Renton, WA 98057 USA

(425) 277-8000 ph.

(425) 277-5280 Fax

Recommended Resources

Bistable circuit b

Monolithic Temperature Sensing Circuit

Spring load sensor circuit

TDA2006 power amplifier circuit

Inverter circuit 4

Comparison Solution: SAI+LM2596 Switching Voltage Regulator Solution: [i=s]This post was last edited by lonerzf on 2014-8-17 17:46[/i] In the previous design process, I encountered a situation where there was no suitable input power supply. At that time, there was only ...; lonerzf Analogue and Mixed Signal

Embedded linux recvfrom problem: S3C6410+3G module, running Linux, using udp to establish a connection with the server, sendto operates normally, data is sent successfully, and the return result is correct. The recvfrom operation fai...; HOHO Linux and Android

Is it possible to use a 5V powered crystal oscillator to provide a clock signal to a 3.3V F2407?: Everyone, I am using the TI dsp of F2407. Because it is powered by 3.3V, I wanted to buy a crystal oscillator with 3.3V power supply, but I couldn't find one. I only bought an active crystal oscillato...; xinyancode DSP and ARM Processors

In XILINX, how to prevent registers from being optimized away?: When I was synthesizing in XST, the registers that were not connected to the output ports were optimized away, but I needed to keep these registers to get some power consumption information.How can I ...; eeleader-mcu FPGA/CPLD

Please help me, how can I establish a kernel debugging relationship between PB5.0 and the development board? Urgent!!!: Please help me, how can I establish a kernel debugging relationship between PB5.0 and the development board? I hope that when the development board is started, PB5.0 can perform single-step debugging ...; lmjxcg Embedded System

WinCE 4.2 IE upgrade problem: During the reference process of wince 4.2, I encountered the following problems. Since the version is too old, it is difficult to find information. I hope experts can give me some advice. 1. The origi...; jgj Embedded System

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components