COAXIAL
SWITCHES
N - TNC - BNC
-
-
STANDARD COAXIAL SPnT up to 12.4 GHz --- RAMSES Concept
R57
Models
3
: Without 50
W
termination
4
: With 50
W
termination
. . . . . . .
Actuator terminal
0
: Solder Pins
5
: DSUB
Connector RF
0
1
2
5
6
:
:
:
:
:
N
up to 3 GHz
N
up to 12.4 GHz
BNC
up to 3 GHz (4)
TNC
up to 3 GHz (4)
TNC
up to 12.4 GHz (4)
Options
Without option
Positive common (2)
Compatible TTL driver(1)
With suppression diodes
With suppression diodes and
positive common (2)
8
: BCD driver TTLcompatible(1)(3)
0
1
2
3
4
:
:
:
:
:
Type
0
1
2
3
4
5
8
9
:
:
:
:
:
:
:
:
Normally open
Normally open + I.C.
Latching
Latching + I.C.
Latching + S. C. O.(1)
Latching + S. C. O. + I.C.(1)
Latching + S. C. O. +A.R.(1)
Latching + S. C. O.+ I.C.+ A.R. (1)
Number of positions
3
4
5
6
7
8
9
0
1
2
(1)
(2)
(3)
(4)
:
:
:
:
:
:
:
:
:
:
3 Positions
4 Positions
5 Positions
6 Positions
7 Positions
8 Positions
9 Positions
10 Positions
11 Positions
12 Positions
Actuator voltage (2)
2
: 12 Vdc
3
: 28 Vdc
I.C.
:
Indicator contact.
S.C.O.
:
Self Cut Off
A.R.
: Automatic Reset
--
:
These models are already equiped with suppression diodes.
:
Standard products are equiped with common minus.
:
Latching BCD driver enables also a manual reset through driver code 0000.
: Available only up to 6 positions.
Latching models have a RESET pin which commands the reset of all positions. This command should be used before switching from
one position to another. If not, two positions will be set at the same time.
Note: During the RESET operation the current is : Setting current x number of positions.
Latching models with AUTOMATIC RESET are available; these products have an internal SET/RESET circuit which automatically set
the desired position and reset the non--selected positions. This option simplifies the use of latching switches by suppressing the
RESET command in switching sequence and reducing the operating current consuption.
For example: During the AUTOMATIC RESET operation, a 28V, 4 positions switch has temporarily a consumption of 250 mA,
during 40 ms maximum only ( See page 56 ).
--
AVAILABILITY OF OPTIONS ACCORDING TO BOTH TYPE AND NUMBER OF POSITIONS
Type
0 or 1
2 or 3
4 or 5
8 or 9
Number of positions
3 to 12
3 to 6
7 to 12
3 to 6
7 to 12
3 to 12
Available options
0 -- 1 -- 2 -- 3 -- 4 -- 8
0 -- 1 -- 2 -- 3 -- 4
0 -- 1 -- 3 -- 4
0 -- 2
Not Available
0 -- 2 -- 8
48
COAXIAL
SWITCHES
N - TNC - BNC
-
-
COAXIAL SPnT up to 12.4 GHz --- RAMSES Concept
GENERAL SPECIFICATIONS - RF PERFORMANCES
Connectors
Number of positions
Frequency range
q
y
g
V.S.W.R. (max)
Insertion Loss (max)
Isolation (min)
dB
dB
GHz
DC- 3
-
1.20
.20
80
3 to 6
DC - 12.4
3- 8
-
1.35
.35
70
8-
-12.4
1.50
.50
60
DC- 3
-
1.30
.30
80
N - BNC - TNC
7 to 10
DC - 8
3- 8
-
1.50
.50
70
DC- 3
-
1.35
.50
70
11 and 12
DC - 8
3- 8
-
1.70
1.00
60
GENERAL SPECIFICATIONS - ADDITIONAL SPECIFICATIONS
Operating mode
Actuator voltage (nominal)
Operating current at 23_C
_
Average power
Peak power
TTL INPUT
Indicator rating
Switching time (max)
Life
SP3 to 6T
SP7 to 12T
Connectors
Actuator terminals
Operating temperature range
Storage temperature range
Impedance
For terminated models
Switching sequence
ms
R573 serie
R574 serie
kW
High level
Low level
Vdc
mA
12
250
Normally open or Latching
Normally open
28
102
See Power Rating Chart page 9
1.5 (1
ms,
1 ‰)
2.2 to 5.5 V ( TTL option ) / 3.5 to 5.5 V ( BCD option )
0 to 0.8 V ( TTL option ) / 0 to 1.5 V ( BCD option )
1 W - 30 V - 100 mA
-
-
15 (for automatic reset models, SP3T to SP6T: 40 ms, SP7T to SP12T: 50 ms)
5 10
6
cycles per way
2 10
6
cycles per way
2 10
6
cycles per way
N, TNC, BNC
Solder pins or DSUB
12
See table below
Latching
28
_
C
_
C
W
-
-40, +85
-
-55, +85
50
50
W
termination
±5%
1 Watt per termination
3 W total power handling per switch
Break Before Make
Operating current at 23°C (mA) SPnT LATCHING
°
12 V
manual reset
SP 3 to 4 T
SP 5 to 8 T
SP 9 to 12 T
320 x n
320 x n
320 x n
automatic
reset
640
960
1280
28 V
manual reset
125 x n
125 x n
125 x n
automatic
reset
250
375
500
n = number of ways
49
stm32/stm8
京公网安备 11010802033920号
EEWORLD
