DW-21-13-G-Q-200 datasheet, PDF

DW-21-13-G-Q-200: DescriptionBoard Stacking Connector, 42 Contact(s), 2 Row(s), Male, Straight, Solder Terminal,; CategoryThe connector The connector; File Size1MB，1 Pages; ManufacturerSAMTEC; Websitehttp://www.samtec.com/; Environmental Compliance

Download Datasheet Parametric View All

DW-21-13-G-Q-200 Overview

Board Stacking Connector, 42 Contact(s), 2 Row(s), Male, Straight, Solder Terminal,

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	SAMTEC
Reach Compliance Code	compli
ECCN code	EAR99
body width	0.296 inch
subject depth	0.2 inch
body length	2.1 inch
Connector type	BOARD STACKING CONNECTOR
Contact to complete cooperation	GOLD (10)
Contact completed and terminated	GOLD (3)
Contact point gender	MALE
Contact material	PHOSPHOR BRONZE
contact mode	RECTANGULAR
Contact style	SQ PIN-SKT
DIN compliance	NO
Filter function	NO
IEC compliance	NO
Insulator color	BLACK
insulator material	GLASS FILLED POLYESTER
JESD-609 code	e4
MIL compliance	NO
Manufacturer's serial number	DW
Plug contact pitch	0.1 inch
Mixed contacts	NO
Installation method	STRAIGHT
Installation type	BOARD
PCB row number	2
Number of rows loaded	2
Options	GENERAL PURPOSE
Terminal pitch	2.54 mm
Termination type	SOLDER
Total number of contacts	42
UL Flammability Code	94V-0

STM32 drives LSM6DSL, and the read FIFO data is always 0: I use STM32 SPI to drive LSM6DSL to read accelerometer and gyroscope data. If FIFO is not used, the data read using its output source registers OUTX_L_G OUTX_H_G, etc. is fine. The configuration is as...; 翱翔云端的鸟 MEMS sensors

Use interrupts to store the received data in the array in order, but when you use the serial port to send the data to the computer, the order is messed up?: [i=s] This post was last edited by ena at 2016-2-18 09:58[/i] volatile unsigned char SZ[5]; volatile char int_flag=0;//int6_flag; char keydisp[5]; static unsigned char read165(void) { unsigned char i,...; ena Microchip MCU

I need some advice from seniors on the timer issue.: StartFragmentMy program generates 4-channel PWM, 2 of which are 90 degrees different from the other 2. The frequency displayed by the oscilloscope is not the 50HZ I set. It is very slow. What's going ...; t_shaojun126 Microcontroller MCU

MSP430F2xxx series FLASH data loss: By chance, I found that the MSP430F2xxx board I made would have the information memory erased for unknown reasons when powered on. Later, I tested several boards and found that some of the boards woul...; xchromosome Embedded System

Principle and composition of pressure sensor: A pressure sensor is a device that detects pressure and converts the pressure signal into an electrical signal and outputs it linearly. Pressure sensors can be divided into mechanical pressure sensors...; cazsensor Industrial Control Electronics

A simple question has me stumped!: Write a low-level software, download it to the microcontroller, and run it automatically when powered on. There are 10 files pre-stored in the CF card. Each time the power is turned on, a different fi...; hjyhjony Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components