ATMEGA168-10PI datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The embedded processor and controller> Microcontrollers and processors> ATMEGA168-10PI

ATMEGA168-10PI: DescriptionMicrocontroller, 8-Bit, FLASH, AVR RISC CPU, 4MHz, CMOS, PDIP28,; CategoryThe embedded processor and controller Microcontrollers and processors; File Size3MB，359 Pages; ManufacturerAtmel (Microchip)

Download Datasheet Parametric Compare View All

ATMEGA168-10PI Overview

Microcontroller, 8-Bit, FLASH, AVR RISC CPU, 4MHz, CMOS, PDIP28,

ATMEGA168-10PI Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Maker	Atmel (Microchip)
package instruction	DIP, DIP28,.3
Reach Compliance Code	compli
bit size	8
CPU series	AVR RISC
JESD-30 code	R-PDIP-T28
JESD-609 code	e0
Number of terminals	28
On-chip program ROM width	16
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Package body material	PLASTIC/EPOXY
encapsulated code	DIP
Encapsulate equivalent code	DIP28,.3
Package shape	RECTANGULAR
Package form	IN-LINE
power supply	2/5 V
Certification status	Not Qualified
RAM (bytes)	1024
rom(word)	8192
ROM programmability	FLASH
speed	4 MHz
Maximum slew rate	12 mA
surface mount	NO
technology	CMOS
Temperature level	INDUSTRIAL
Terminal surface	Tin/Lead (Sn/Pb)
Terminal form	THROUGH-HOLE
Terminal pitch	2.54 mm
Terminal location	DUAL

Preview

Download Datasheet

View All

Features

•

High Performance, Low Power AVR

8-Bit Microcontroller

•

Advanced RISC Architecture

– 131 Powerful Instructions – Most Single Clock Cycle Execution

– 32 x 8 General Purpose Working Registers

– Fully Static Operation

– Up to 20 MIPS Throughput at 20 MHz

– On-chip 2-cycle Multiplier

Non-volatile Program and Data Memories

– 4/8/16K Bytes of In-System Self-Programmable Flash (ATmega48/88/168)

Endurance: 10,000 Write/Erase Cycles

– Optional Boot Code Section with Independent Lock Bits

In-System Programming by On-chip Boot Program

True Read-While-Write Operation

– 256/512/512 Bytes EEPROM (ATmega48/88/168)

Endurance: 100,000 Write/Erase Cycles

– 512/1K/1K Byte Internal SRAM (ATmega48/88/168)

– Programming Lock for Software Security

Peripheral Features

– Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode

– One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture

Mode

– Real Time Counter with Separate Oscillator

– Six PWM Channels

– 8-channel 10-bit ADC in TQFP and QFN/MLF package

– 6-channel 10-bit ADC in PDIP Package

– Programmable Serial USART

– Master/Slave SPI Serial Interface

– Byte-oriented 2-wire Serial Interface

– Programmable Watchdog Timer with Separate On-chip Oscillator

– On-chip Analog Comparator

– Interrupt and Wake-up on Pin Change

Special Microcontroller Features

– Power-on Reset and Programmable Brown-out Detection

– Internal Calibrated Oscillator

– External and Internal Interrupt Sources

– Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and

Standby

I/O and Packages

– 23 Programmable I/O Lines

– 28-pin PDIP, 32-lead TQFP and 32-pad QFN/MLF

Operating Voltage:

– 1.8 - 5.5V for ATmega48V/88V/168V

– 2.7 - 5.5V for ATmega48/88/168

Temperature Range:

– -40

C to 85

Speed Grade:

– ATmega48V/88V/168V: 0 - 4 MHz @ 1.8 - 5.5V, 0 - 10 MHz @ 2.7 - 5.5V

– ATmega48/88/168: 0 - 10 MHz @ 2.7 - 5.5V, 0 - 20 MHz @ 4.5 - 5.5V

•

8-bit

Microcontroller

with 8K Bytes

In-System

Programmable

Flash

ATmega48/V

ATmega88/V

ATmega168/V

Preliminary

•

Rev. 2545E–AVR–02/05

The AVR core combines a rich instruction set with 32 general purpose working registers. All the

32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent

registers to be accessed in one single instruction executed in one clock cycle. The resulting

architecture is more code efficient while achieving throughputs up to ten times faster than con-

ventional CISC microcontrollers.

The ATmega48/88/168 provides the following features: 4K/8K/16K bytes of In-System Program-

mable Flash with Read-While-Write capabilities, 256/512/512 bytes EEPROM, 512/1K/1K bytes

SRAM, 23 general purpose I/O lines, 32 general purpose working registers, three flexible

Timer/Counters with compare modes, internal and external interrupts, a serial programmable

USART, a byte-oriented 2-wire Serial Interface, an SPI serial port, a 6-channel 10-bit ADC (8

channels in TQFP and QFN/MLF packages), a programmable Watchdog Timer with internal

Oscillator, and five software selectable power saving modes. The Idle mode stops the CPU

while allowing the SRAM, Timer/Counters, USART, 2-wire Serial Interface, SPI port, and inter-

rupt system to continue functioning. The Power-down mode saves the register contents but

freezes the Oscillator, disabling all other chip functions until the next interrupt or hardware reset.

In Power-save mode, the asynchronous timer continues to run, allowing the user to maintain a

timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the

CPU and all I/O modules except asynchronous timer and ADC, to minimize switching noise dur-

ing ADC conversions. In Standby mode, the crystal/resonator Oscillator is running while the rest

of the device is sleeping. This allows very fast start-up combined with low power consumption.

The device is manufactured using Atmel’s high density non-volatile memory technology. The

On-chip ISP Flash allows the program memory to be reprogrammed In-System through an SPI

serial interface, by a conventional non-volatile memory programmer, or by an On-chip Boot pro-

gram running on the AVR core. The Boot program can use any interface to download the

application program in the Application Flash memory. Software in the Boot Flash section will

continue to run while the Application Flash section is updated, providing true Read-While-Write

operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a

monolithic chip, the Atmel ATmega48/88/168 is a powerful microcontroller that provides a highly

flexible and cost effective solution to many embedded control applications.

The ATmega48/88/168 AVR is supported with a full suite of program and system development

tools including: C Compilers, Macro Assemblers, Program Debugger/Simulators, In-Circuit Emu-

lators, and Evaluation kits.

2.2

Comparison Between ATmega48, ATmega88, and ATmega168

The ATmega48, ATmega88 and ATmega168 differ only in memory sizes, boot loader support,

and interrupt vector sizes.

Table 2-1

summarizes the different memory and interrupt vector sizes

for the three devices.

Table 2-1.

Device

ATmega48

ATmega88

ATmega168

Memory Size Summary

Flash

4K Bytes

8K Bytes

16K Bytes

EEPROM

256 Bytes

512 Bytes

RAM

512 Bytes

1K Bytes

Interrupt Vector Size

1 instruction word/vector

2 instruction words/vector

ATmega88 and ATmega168 support a real Read-While-Write Self-Programming mechanism.

There is a separate Boot Loader Section, and the SPM instruction can only execute from there.

ATmega48/88/168

2545E–AVR–02/05

ATmega48/88/168

In ATmega48, there is no Read-While-Write support and no separate Boot Loader Section. The

SPM instruction can execute from the entire Flash.

2.3

2.3.1

Pin Descriptions

VCC

Digital supply voltage.

2.3.2

GND

Ground.

2.3.3

Port B (PB7..0) XTAL1/XTAL2/TOSC1/TOSC2

Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The

Port B output buffers have symmetrical drive characteristics with both high sink and source

capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up

resistors are activated. The Port B pins are tri-stated when a reset condition becomes active,

even if the clock is not running.

Depending on the clock selection fuse settings, PB6 can be used as input to the inverting Oscil-

lator amplifier and input to the internal clock operating circuit.

Depending on the clock selection fuse settings, PB7 can be used as output from the inverting

Oscillator amplifier.

If the Internal Calibrated RC Oscillator is used as chip clock source, PB7..6 is used as TOSC2..1

input for the Asynchronous Timer/Counter2 if the AS2 bit in ASSR is set.

The various special features of Port B are elaborated in

”Alternate Functions of Port B” on page

and

”System Clock and Clock Options” on page 25.

2.3.4

Port C (PC5..0)

Port C is a 7-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The

PC5..0 output buffers have symmetrical drive characteristics with both high sink and source

capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up

resistors are activated. The Port C pins are tri-stated when a reset condition becomes active,

even if the clock is not running.

2.3.5

PC6/RESET

If the RSTDISBL Fuse is programmed, PC6 is used as an I/O pin. Note that the electrical char-

acteristics of PC6 differ from those of the other pins of Port C.

If the RSTDISBL Fuse is unprogrammed, PC6 is used as a Reset input. A low level on this pin

for longer than the minimum pulse length will generate a Reset, even if the clock is not running.

The minimum pulse length is given in

Table 8-1 on page 44.

Shorter pulses are not guaranteed

to generate a Reset.

The various special features of Port C are elaborated in

”Alternate Functions of Port C” on page

75.

2.3.6

Port D (PD7..0)

Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The

Port D output buffers have symmetrical drive characteristics with both high sink and source

capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up

2545E–AVR–02/05

ATMEGA168-10PI Related Products

	ATMEGA168-10PI	ATMEGA168-10AI	ATMEGA168-10MI
Description	Microcontroller, 8-Bit, FLASH, AVR RISC CPU, 4MHz, CMOS, PDIP28,	Microcontroller, 8-Bit, FLASH, AVR RISC CPU, 4MHz, CMOS, PQFP32,	Microcontroller, 8-Bit, FLASH, AVR RISC CPU, 4MHz, CMOS, PQCC32,
Is it Rohs certified?	incompatible	incompatible	incompatible
Maker	Atmel (Microchip)	Atmel (Microchip)	Atmel (Microchip)
package instruction	DIP, DIP28,.3	QFP, TQFP32,.35SQ,32	QCCN, LCC32,.2SQ,20
Reach Compliance Code	compli	compli	compli
bit size	8	8	8
CPU series	AVR RISC	AVR RISC	AVR RISC
JESD-30 code	R-PDIP-T28	S-PQFP-G32	S-PQCC-N32
JESD-609 code	e0	e0	e0
Number of terminals	28	32	32
On-chip program ROM width	16	16	16
Maximum operating temperature	85 °C	85 °C	85 °C
Minimum operating temperature	-40 °C	-40 °C	-40 °C
Package body material	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY
encapsulated code	DIP	QFP	QCCN
Encapsulate equivalent code	DIP28,.3	TQFP32,.35SQ,32	LCC32,.2SQ,20
Package shape	RECTANGULAR	SQUARE	SQUARE
Package form	IN-LINE	FLATPACK	CHIP CARRIER
power supply	2/5 V	2/5 V	2/5 V
Certification status	Not Qualified	Not Qualified	Not Qualified
RAM (bytes)	1024	1024	1024
rom(word)	8192	8192	8192
ROM programmability	FLASH	FLASH	FLASH
speed	4 MHz	4 MHz	4 MHz
Maximum slew rate	12 mA	12 mA	12 mA
surface mount	NO	YES	YES
technology	CMOS	CMOS	CMOS
Temperature level	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL
Terminal surface	Tin/Lead (Sn/Pb)	Tin/Lead (Sn/Pb)	Tin/Lead (Sn/Pb)
Terminal form	THROUGH-HOLE	GULL WING	NO LEAD
Terminal pitch	2.54 mm	0.8 mm	0.5 mm
Terminal location	DUAL	QUAD	QUAD

Recommended Resources

NTC thermistor temperature controller circuit diagram

Long-distance FM transmitter circuit diagram made of high-frequency triode

Multifunctional refrigerator DC voltage controller circuit diagram composed of 555

Single Supply Bridge Sensor Transmitter Circuit

Headphone amplifier circuit

Method of measuring ABS wheel speed sensor signal using automobile oscilloscope: The anti-lock brake system (ABS) of a car is to automatically control the braking force when the car brakes, so that the wheels are not locked and are in a state of rolling and sliding (slip rate is a...; Micsig麦科信 Automotive Electronics

The difference between motion control of PLC and motion controller: In simple terms, the full name of PLC is Programmable Logic Controller. It is responsible for logic control. It is weak in motion control, although many high-end PLCs already have motion control modul...; crt13652346449 Integrated technical exchanges

Electronics Development and Design Experience: Trivia 1: Cost saving phenomenon 1: It doesn't matter what value these pull-up/pull-down resistors are, just pick an integer of 5K Comment: There is no 5K value on the market, the closest is 4.99K (1%...; 呱呱 MCU

CC2530 Data Sheet (Chinese version): For your reference, if you are interested in Zigbee, you can add my QQ (284382376) to discuss with me....; zhaofaohua RF/Wirelessly

A novice asks for help, a problem encountered in the example: When I follow the steps in the article below: http://www.microsoft.com/china/MSDN/library/windev/WindowsCE/windowscedrivers.mspx When I compile the newly created TuxTest project, I get several errors ...; lijb920 Embedded System

A very practical summary! One article covers all rectifier and filter circuits: Basic circuit:Generally, DC stabilized power supplies use 220V mains electricity as power supply, which is then transmitted to the voltage stabilizer circuit for voltage stabilization after voltage tr...; eric_wang Power technology

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components