DS80C320-ECR datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > semiconductor> The embedded processor and controller> DS80C320-ECR

Preview

DS80C320-ECR: Description8-BIT, 25 MHz, MICROCONTROLLER, PQFP44; Categorysemiconductor The embedded processor and controller; File Size1MB，175 Pages; ManufacturerDALLAS; Websitehttp://www.dalsemi.com

Download Datasheet View All

DS80C320-ECR Overview

8-BIT, 25 MHz, MICROCONTROLLER, PQFP44

Preview

Download Datasheet

View All

….

User’s Guide

www.dalsemi.com

High-Speed Microcontroller

User Guide

SmartSocket 16K/64K

SECTION 1: INTRODUCTION

The Dallas Semiconductor High-Speed Microcontroller is an 8051-compatible device that provides

improved performance and power consumption compared to the original version. It retains instruction set

and object code compatibility with the 8051, yet performs the same operations in fewer clock cycles.

Consequently, more throughput is possible for the same crystal speed. As an alternative, the High-Speed

Microcontroller can be run slowly to save power. The more efficient design allows a much slower crystal

speed to get the same results as an original 8051, using much less power.

The fundamental innovation of the High-Speed Microcontroller is the use of only four clocks per

instruction cycle compared with twelve for the original 8051. This results in up to 3 times improvement

in performance. In addition, the High-Speed Microcontroller is updated with several new peripherals and

features while providing all of the standard features of an 80C32. These include 256 bytes of on-chip

RAM, 32 I/O ports, three 16-bit timer/counters, and an on-chip UART. All devices provide 256 bytes of

RAM for variables and stack. 128 bytes can be reached using direct addressing and 128 using indirect

addressing.

In addition to improved efficiency, members of the High-Speed Microcontroller family can operate at a

maximum clock rate of 33 or 40 MHz. Combined with the 3 times performance, this allows for a

maximum performance equivalent to a 99 or 120 MHz 8051. This level of computing power is

comparable to many 16-bit processors, but without the added expense and complexity if implementing a

16-bit interface.

A number of peripherals were added to the original 80C32 core when designing the High-Speed

Microcontroller family. Some devices have a programmable watchdog Timer to supervise the system. It

will count up to a user programmable interval and then reset the CPU unless cleared by software. Other

features such as a second, full-function UART and dual data pointers are available to minimize external

interrupts allows greater flexibility in dealing with external events.

Some members of the High-Speed Microcontroller family incorporate Power Management Modes which

allow the device to dynamically vary the internal clock speed from 4 clocks per cycle (default) to 64 or

1024 clocks per cycle. Because power consumption is directly proportional to clock speed, the device

can reduce its operating frequency during periods of little or no activity. This greatly reduces power

consumption. The switch-back feature allows the device to quickly return in divide by 4 mode upon

receipt of an interrupt or serial port activity, allowing the device to respond to external events while in

Power Management Mode.

Various memory configurations are available with the High-Speed Microcontroller family. EPROM and

Mask programmable ROM versions are available for program memory. Some versions incorporate

extended MOVX SRAM on-chip, reducing or eliminating the need for external data memory. This

memory can be made nonvolatile in the DS87C530 through the use of an external lithium battery.

1 of 175

092299

High-Speed Microcontroller User’s Guide

SECTION 3: ARCHITECTURE

The High-Speed Microcontroller is based on the industry standard 80C52. The core is an accumulator

based architecture using internal registers for data storage and peripheral control. It executes the standard

8051 instruction set. This section provides a brief description of each architecture feature. Details

concerning the programming model, instruction set, and register description are provided in Section 4.

ALU

The ALU is responsible for math functions, comparisons, and general decision making in the High-Speed

Microcontroller. The ALU is not explicitly used by software. Instruction decoding prepares the ALU

automatically and passes it the appropriate data. The ALU primarily uses two special function registers

(SFRs) as the source and destination for all operations. These are the Accumulator and B register. The

ALU also provides status information in the Program Status Register. The SFRs are described below.

SPECIAL FUNCTION REGISTERS

All peripherals and operations that are not explicit instructions in the High-Speed Microcontroller are

controlled via Special Function Registers (SFRs). All SFRs are described in Section 4. The most

commonly used registers that are basic to the architecture are also described below.

Accumulator

The Accumulator is the primary register used in the High-Speed Microcontroller. It is the source and

destination of most math, data movement, decisions, and other operations. Although it can be bypassed,

most high-speed instructions require the use of the Accumulator (ACC) as one argument.

B Register

The B register is used as the second 8-bit argument in multiply and divide operations. When not used for

these purposes, the B register can be used as a general purpose register.

Program Status Word

The Program Status Word holds a selection of bit flags that include the Carry Flag, Auxiliary Carry Flag,

General Purpose Flag, Register Bank Select, Overflow Flag, and Parity Flag.

Data Pointer(s)

The Data Pointer is used to designate a memory address for the MOVX instruction. This address can

point to a MOVX RAM location, either on- or off-chip, or a memory mapped peripheral. When moving

data from one memory area to another or from memory to a memory mapped peripheral, a pointer is

needed for both the source and destination. Thus the High-Speed Microcontroller offers two data

pointers. The user selects the active pointer via a dedicated SFR bit.

Stack Pointer

The microcontroller provides a Stack in the scratchpad RAM area discussed below. The Stack Pointer

denotes the register location at the top of the Stack, which is the last used value. The user can place the

Stack anywhere in scratchpad RAM by setting the Stack Pointer to that location.

I/O Ports

The standard High-Speed Microcontroller offers four 8-bit I/O ports. ROM less versions use Port 0 and

Port 2 as address and data busses. In those versions, only two ports are available for general purpose I/O.

Each I/O port is a Special Function Register that can be written or read. The I/O port has a latch that

3 of 175

High-Speed Microcontroller User’s Guide

retains the value which software writes. In general, during a read operation, software reads the state of

the external pin. Each port is represented by a SFR location.

Timer/Counters

Three 16-bit Timer/Counters are available in the High-Speed Microcontroller. Each timer is contained in

two SFR locations that can be written or read by software. The timers are controlled by other SFRs

described in Section 4.

UARTs

The High-Speed Microcontroller provides one or two UARTs. These are controlled and accessed as

SFRs. Each UART has an address that is used to read or write the UART. The same address is used for

both read and write operations. The microcontroller distinguishes between a read and a write by the

instruction. Each UART is controlled by its own SFR control register.

SCRATCHPAD REGISTERS (RAM)

The High-Speed Core provides 256 bytes of Scratchpad RAM for general purpose data and variable

storage. The first 128 bytes are directly available to software. The second 128 are available through

indirect addressing discussed below. Selected portions of this RAM have other optional functions.

Stack

The stack is a RAM area that the microcontroller uses to store return address information during Calls

and Interrupts. The user can also place variables on the stack when necessary. The Stack Pointer

mentioned above designates the RAM location that is the top of the stack. Thus, depending on the value

of the Stack Pointer, the stack can be located anywhere in the 256 bytes of RAM. A common location

would be in the upper 128 bytes of RAM, as these are accessible through indirect addressing only.

Working Registers

The first thirty-two bytes of the Scratchpad RAM can be used as four banks of eight Working Registers

for high speed data movement. Using four banks, software can quickly change context by simply

changing to a different bank. In addition to the Accumulator, the Working Registers are commonly used

as data source or destination. Some of the Working Registers can also be used as pointers to other RAM

locations (indirect addressing).

PROGRAM COUNTER

The Program Counter (PC) is a 16-bit value that designates the next program address to be fetched. On-

chip hardware automatically increments the PC value to move to the next ROM location.

ADDRESS/DATA BUS

The High-Speed Microcontroller addresses a 64KB program and 64KB data memory area. In the

ROMless versions, all memory is outside. Other versions use a combination of internal and external

memory. When external memory is accessed, Ports 0 and 2 are used as a multiplexed address and data

bus. Port 2 provides the address MSB. Even versions with internal memory can use the bus on Ports 0

and 2 to access more memory.

WATCHDOG TIMER

The Watchdog Timer provides a supervisory function for applications that cannot afford to run out of

control. The Watchdog Timer is a programmable free running timer. If allowed to reach the termination

of its count, if enabled, the Watchdog will reset the CPU. Software must prevent this by cleaning or

resetting the Watchdog prior to its time-out.

4 of 175

High-Speed Microcontroller User’s Guide

POWER MONITOR

Some members of the High-Speed Microcontroller family incorporate a band-gap reference and analog

circuitry to monitor the power supply conditions. V

begins to drop out of tolerance, the Power Monitor

will issue an optional early warning Power-fail interrupt. If power continues to fall, the Power Monitor

will invoke a reset condition. This will remain until power returns to normal operating voltage. The

Power Monitor also functions on power-up, holding the microcontroller in a reset state until power is

stable.

INTERRUPTS

The High-Speed Microcontroller is capable of evaluating a number of interrupt sources simultaneously.

Each version of the High-Speed Microcontroller provides a different number of interrupt sources. Each

interrupt has an associated interrupt vector, flag, priority, and enable. These interrupts can be globally

enabled or disabled.

TIMING CONTROL

The High-Speed Microcontroller provides an on-chip oscillator for use with an external crystal. This can

be bypassed by injecting a clock source into the XTAL 1 pin. The clock source is used to create machine

cycle timing (four clocks), ALE,

PSEN

, Watchdog, Timer, and serial baud rate timing. In addition, some

devices incorporate an on-chip ring oscillator which can be used to provide an approximately 2-4 MHz

clock source.

REAL-TIME CLOCK

The DS87C530 incorporates a real-time clock (RTC), which is accessed via SFR locations. The RTC is

divided into hour, minute, second, and subsecond registers, and also incorporates a 65536 day calendar.

Alarm registers allow the RTC to issue interrupts at a specific time once a day, or as a recurring alarm

every hour, minute or second. An external watch crystal and lithium power source allow the processor to

maintain timekeeping in the absence of V

FEATURE SUMMARY

The High-Speed Microcontroller family offers a combination of features and peripherals as shown in

Table 3-1. This User’s Guide is designed as a comprehensive guide covering all features available in the

High-Speed Microcontroller family. The designer should investigate the specific data sheet to determine

which features are available on a particular device. Detailed information about newer members of the

product family may be provided in separate documents until they can be assimlilated into the High-Speed

Microcontroller User’s Guide.

5 of 175

Recommended Resources

Relay inverse time overcurrent protection circuit a

Wire-controlled music lantern circuit (1)

Delayed light circuit using relay (7)

Monostable trigger timing circuit

Car video recorder TV inverter circuit diagram

Kitchen smoke exhaust circuit

It's hard to survive: It's really hard to find a job, especially for my special situation. I'm a troublemaker in school, I don't have a scholarship, I'm not in the student union, and I don't have a high degree. Even if I h...; cl17726 Talking

Can you guys help me figure out how to improve this?: ...; huzl Analog electronics

EEWORLD DIY-Make an environmental parameter storage system: I'd like to take this opportunity to share a recent work I made. Function: Collect sensor data and store it. Hardware: Main control: Arduino development board. Sensors: temperature sensor DHT22, PM2.5...; sanhuasr DIY/Open Source Hardware

Participate in MSP430F5529 training, gain knowledge, free gifts, super low group, grab the building! (The list of winners of the fifth phase has been announced): Participate in TI MSP430F5529 training (learning link: [url=https://www.eeworld.com.cn/training/2013/0222/movie_109.html]https://www.eeworld.com.cn/training/2013/0222/movie_109.html[/url]) [b][font=微软...; EEWORLD社区 Microcontroller MCU

f769 review basic driver chapter - general timer: From the datasheet of f769, we know that there are 15 timers. Among them, timer2, 3, 4, and 5 are general timers. The detailed classification is 16-bit (TIM3, TIM4) or 32-bit (TIM2 and TIM5). This pos...; star_66666 stm32/stm8

BMW original fault detector (GT1) maintenance: A friend of mine has a broken GT1. It started with a power supply failure because a gong cap on the wireless network card socket fell off, shorting something and burning the 3.3V power supply circuit....; qs7779 Automotive Electronics

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components