EEWORLDEEWORLDEEWORLD

Part Number

Search

SC50M390APF11320

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 50V, 20% +Tol, 20% -Tol, 390uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size66KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SC50M390APF11320 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 50V, 20% +Tol, 20% -Tol, 390uF, Through Hole Mount, ROHS COMPLIANT

SC50M390APF11320 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance390 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
ESR45 mΩ
leakage current0.195 mA
Manufacturer's serial numberSC
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTAPE
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)50 V
ripple current1660 mA
surface mountNO
Delta tangent0.08
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
Miniature Size Aluminum
Electrolytic Capacitors
SC
[ For Low Impedance and Low E.S.R
Suitable for Output of Mother Board ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For High Frequency Applications
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
Working Voltage : 6.3 ~ 100V
Rate Capacitance Range : 4.7 ~ 15000µF
Capacitance Tolerance : -20 ~ +20%
DESCRIPTION
Used in switching regulator applications in com-
puters. Especially for high frequency.
Low impedance and E.S.R., high permissible ripple
current at high frequency and higher operating
temperature (-40°C to +105°C).
High Temperature Load Life at 105°C for 3000
Hours
DC Leakage Current (µA) : I = 0.01 CV(µA) or 3µA Whichever is greater.
( Measurements shall be Made After a 2 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 6.3
10
16
25
35
50
63
80
100
D.F (%) : 15
14
12
10
10
8
8
7
7
For capacitor whose capacitance exceeds 2000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
WV (V)
:
6.3
10
10
8
16
5
25
4
35
4
50
4
63
4
100
4
Impedance : Z - 40°C / Z + 20°C
Load Life : 3000 Hours at 105°C Assured with Full Rated Maximum Ripple Current Applied
Multiplier for Ripple Current
Frequency(Hz)
~4.7µF
5.6~33µF
34~330µF
331~1000µF
1200µF Higher
50
0.30
0.40
0.60
0.65
0.85
120
0.40
0.50
0.70
0.80
0.90
300
0.50
0.60
0.80
0.90
0.95
1K
0.70
0.80
0.90
0.98
0.98
10K 100K
0.80 1.00
0.90 1.00
0.95 1.00
1.00 1.00
1.00 1.00
5 x 11 ~ 10 x 12 : Life = 2000 Hours
10 x 15 or Higher : Life = 3000 Hours
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Temperature(°C)
Factor
65
1.80
85
1.50
105
1.00
Dimensions : mm
Rubber Stand-off
4.0
Rubber End Seal
DIAGRAM OF DIMENSIONS
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
5.0
6.3
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F 0.5
F 0.5
0.4Max.
15Min.
0.6
L
15Min.
5Min.
D 0.5
L
5Min.
D 0.5
7.5
10.0
0.8
0.8
What is the difference between the circuit diagrams of the matrix keyboard scanning method and the line inversion method?
Below is the program for the line reversal method. I used this function in the program but it went wrong. The high four pins are always kept at a low level. There is no response when I press the key. ...
leoyang Embedded System
Helper2416 development board porting minigui3.0.12 Part 2: Porting to the development board
[i=s]This post was last edited by Gyroxp on 2015-1-25 11:51[/i] The second stage: porting minigui to the Helper2416 development board. It is a little more troublesome to run minigui on the development...
Gyroxp Embedded System
Basic knowledge of power supply
The texture is quite hard, so I organized a world document....
wanggq Power technology
Does anyone have a download link for Protel DXP?
Hello everyone, does anyone have a real download address for Protel DXP? I searched online, but the results were not ideal. Either it cannot be installed, or it requires a registration code. It is rea...
gxlcgxlc MCU
How to make a variable frequency power supply?
[i=s] This post was last edited by paulhyde on 2014-9-15 09:09 [/i] Please give me a plan for making a 30W variable frequency power supply, preferably with a circuit design diagram :)...
zxllove23 Electronics Design Contest
Why does it always say that RCC_APB1Periph_USART4 is not defined?
I searched for the stm32f10x_rcc.h file and it is indeed not defined. What's going on?...
yilingtang stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 17  1469  2298  827  235  1  30  47  17  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号