EEWORLDEEWORLDEEWORLD

Part Number

Search

SE-K10M22BPSM511

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 10V, 20% +Tol, 20% -Tol, 22uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size60KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SE-K10M22BPSM511 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 10V, 20% +Tol, 20% -Tol, 22uF, Through Hole Mount, ROHS COMPLIANT

SE-K10M22BPSM511 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance22 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.0144 mA
Manufacturer's serial numberSE-K
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)10 V
ripple current45 mA
surface mountNO
Delta tangent0.22
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SE-K
[ For General ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors Rated Voltage up to 450V
Miniature Size Aluminum
Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C / -25° ~ +105°C
Working Voltage : 6.3 ~ 250V / 350 ~ 450V
Rate Capacitance Range : 0.47 ~ 15000µF / 0.47 ~ 150µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.01CV + 3 / 0.03CV + 10
( After 2 Minutes Application of DC Working Voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
W V (V) : 6.3
10
16
25
35
50
63
80
100 160 ~ 250 350 ~ 450
D.F (%) : 26
22
18
16
14
12
10
10
10
15
20
For capacitor whose capacitance excceds 1000 µF. The value of DF(%) is increased by 2% for every
addition of 1000 µF.
Load Life : 1000 Hours at Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 500 Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
DESCRIPTION
Lower-cost capacitors expressly intended for high
density printed circuit board.
Ideally suited for general-purpose applications,
entertainment electronics.
Feature High CV Product with Moderate Cost
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
6.3~100V 100~680µF
6.3~110V 1000~22000µF
160~450V ALL Cap(µF)
120
1.00
1.00
1.00
1.00
300
1.20
1.10
1.05
1.05
1K 10K~100K
1.30
1.45
1.15
1.25
1.10
1.15
1.10
1.50
Temperature(°C)
Factor
65
1.80
85
1.40
105
1.00
DIAGRAM OF DIMENSIONS
4.0
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dimensions : mm
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
About the relationship between int13 interrupt and hard disk underlying driver
Hello everyone, I just started learning drivers, and I don't quite understand some basic concepts. Please help me, thank you. My question is what is the relationship between the BIOS's int13 and the h...
chely Embedded System
I can't understand the chip manual, please help.
I was reading the chip manual for a programmable gain amplifier, VCA824, and there was a table in it that I couldn't understand....
wrx_vigos Analog electronics
Mitsubishi servo voltage problem
I use a Mitsubishi J3 driver, the input voltage is three-phase 200V (measured with a voltmeter), the bus voltage Pn is about 280V when the driver self-tests, is this self-tested bus voltage the peak v...
eeleader Industrial Control Electronics
Ask about CPLD and other precision frequency measurement issues
I am a beginner in CPLD. I wrote a frequency measurement program with equal precision. The gate time is given by the microcontroller. After completion, the CPLD data is transmitted to the microcontrol...
zlh6630 FPGA/CPLD
About Spread Spectrum Function
Regarding the spread spectrum of the chip, I saw two concepts in the manual, one is the spread spectrum frequency, and the other is the spread spectrum Modulation Width. I am a little confused about t...
小太阳yy Switching Power Supply Study Group
Consultation on communication solutions under embedded Linux, thanks to the experts for their advice
Consultation on communication solutions under embedded linux, thanks to the experts for their guidance------------------------------------------------------------------------------- /Goal/: Implement ...
ckuangling Linux and Android

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1006  2724  193  908  2780  21  55  4  19  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号