EEWORLDEEWORLDEEWORLD

Part Number

Search

SE-K10M330B1FM611

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 10V, 20% +Tol, 20% -Tol, 330uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size60KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance  
Download Datasheet Parametric View All

SE-K10M330B1FM611 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 10V, 20% +Tol, 20% -Tol, 330uF, Through Hole Mount, ROHS COMPLIANT

SE-K10M330B1FM611 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance330 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.076 mA
Manufacturer's serial numberSE-K
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)10 V
ripple current160 mA
surface mountNO
Delta tangent0.22
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SE-K
[ For General ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors Rated Voltage up to 450V
Miniature Size Aluminum
Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C / -25° ~ +105°C
Working Voltage : 6.3 ~ 250V / 350 ~ 450V
Rate Capacitance Range : 0.47 ~ 15000µF / 0.47 ~ 150µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.01CV + 3 / 0.03CV + 10
( After 2 Minutes Application of DC Working Voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
W V (V) : 6.3
10
16
25
35
50
63
80
100 160 ~ 250 350 ~ 450
D.F (%) : 26
22
18
16
14
12
10
10
10
15
20
For capacitor whose capacitance excceds 1000 µF. The value of DF(%) is increased by 2% for every
addition of 1000 µF.
Load Life : 1000 Hours at Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 500 Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
DESCRIPTION
Lower-cost capacitors expressly intended for high
density printed circuit board.
Ideally suited for general-purpose applications,
entertainment electronics.
Feature High CV Product with Moderate Cost
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
6.3~100V 100~680µF
6.3~110V 1000~22000µF
160~450V ALL Cap(µF)
120
1.00
1.00
1.00
1.00
300
1.20
1.10
1.05
1.05
1K 10K~100K
1.30
1.45
1.15
1.25
1.10
1.15
1.10
1.50
Temperature(°C)
Factor
65
1.80
85
1.40
105
1.00
DIAGRAM OF DIMENSIONS
4.0
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dimensions : mm
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
How do drivers make an application run?
How does a driver make an application run? I have seen a PDA where pressing a button would pop up a shutdown application interface. In general, it should be how the driver sends a message to the upper...
feeler Embedded System
How to make the WiFi network card automatically connect to the WiFi wireless router in Linux embedded system
How to make the WiFi network card automatically connect to the WiFi wireless router in Linux embedded system...
郭家裕 Embedded System
Why is there a 30-second limit on forum searches?
When I searched the first keyword, there was no result, so I changed it and searched again. Then the message "Sorry" appeared....
dontium Suggestions & Announcements
HID device communication problems
I simulated my own hardware device into a HID device, and then failed to communicate with it through IOCTL_HID_SET_FEATURE and IOCTL_HID_GET_FEATURE at the kernel layer, and the return error value was...
occean Embedded System
International electronic standards for pad requirements
[color=#444444]The IEC International Electrotechnical Commission's 6118 standard recognizes the need for different goals for solder fillet or pad protrusion conditions. This new international standard...
qwqwqw2088 PCB Design
Ask the problem of multiple display terminals!
More than 50 touch screens! How can we achieve that one server sends different data to the touch screen, and the touch screen sends different data to one server? Or, touch screen + single chip microco...
碧海沉天 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2149  31  1511  2571  1684  44  1  31  52  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号