SE-K35M150BPFL1012 datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> SE-K35M150BPFL1012

SE-K35M150BPFL1012: DescriptionAluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 35V, 20% +Tol, 20% -Tol, 150uF, Through Hole Mount, ROHS COMPLIANT; CategoryPassive components capacitor; File Size60KB，3 Pages; ManufacturerYAGEO; Websitehttp://www.yageo.com/; Environmental Compliance

Download Datasheet Parametric View All

SE-K35M150BPFL1012 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 35V, 20% +Tol, 20% -Tol, 150uF, Through Hole Mount, ROHS COMPLIANT

SE-K35M150BPFL1012 Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	YAGEO
package instruction	,
Reach Compliance Code	compliant
ECCN code	EAR99
capacitance	150 µF
Capacitor type	ALUMINUM ELECTROLYTIC CAPACITOR
dielectric materials	ALUMINUM (WET)
leakage current	0.115 mA
Manufacturer's serial number	SE-K
Installation features	THROUGH HOLE MOUNT
negative tolerance	20%
Number of terminals	2
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
Package shape	CYLINDRICAL PACKAGE
method of packing	BULK
polarity	POLARIZED
positive tolerance	20%
Rated (DC) voltage (URdc)	35 V
ripple current	190 mA
surface mount	NO
Delta tangent	0.35
Terminal shape	WIRE

Preview

Download Datasheet

View All

YAGEO CORPORATION

ALUMINUM ELECTROLYTIC CAPACITORS

SE-K

[ For General ]

105°C Single-Ended Lead Aluminum Electrolytic Capacitors Rated Voltage up to 450V

Miniature Size Aluminum

Electrolytic Capacitors

ELECTRICAL CHARACTERISTICS

Operating Temperature : -40° ~ +105°C / -25° ~ +105°C

Working Voltage : 6.3 ~ 250V / 350 ~ 450V

Rate Capacitance Range : 0.47 ~ 15000µF / 0.47 ~ 150µF

Capacitance Tolerance : -20 ~ +20%

DC Leakage Current (µA) : I = 0.01CV + 3 / 0.03CV + 10

( After 2 Minutes Application of DC Working Voltage at 25°C )

Dissipation Factor : at 120 Hz, 25°C

W V (V) : 6.3

100 160 ~ 250 350 ~ 450

D.F (%) : 26

For capacitor whose capacitance excceds 1000 µF. The value of DF(%) is increased by 2% for every

addition of 1000 µF.

Load Life : 1000 Hours at Assured with Full Rated Maximum Ripple Current Applied

(a) Capacitance Change : Within 20% of Initial Value

(b) Dissipation Factor : Not Exceed 200% of Initial Requirement

Shelf Life : 500 Hours, No Voltage Applied

(a) Capacitance Change : Within 20% of Initial Value

(b) Dissipation Factor : Not Exceed 200% of Initial Requirement

DESCRIPTION

Lower-cost capacitors expressly intended for high

density printed circuit board.

Ideally suited for general-purpose applications,

entertainment electronics.

Feature High CV Product with Moderate Cost

Multiplier for Ripple Current

Frequency (Hz)

6.3~100V Below~68µF

6.3~100V 100~680µF

6.3~110V 1000~22000µF

160~450V ALL Cap(µF)

120

1.00

300

1.20

1.10

1.05

1K 10K~100K

1.30

1.45

1.15

1.25

1.10

1.15

1.10

1.50

Temperature(°C)

Factor

1.80

1.40

105

1.00

DIAGRAM OF DIMENSIONS

Dø

4.0

5.0

6.0

8.0

10.0

12.0

13.0

16.0

18.0

22.0

1.5

2.0

2.5

3.5

5.0

dø

0.45

0.5

Rubber Stand-off

Vinyl Sleeve

(P.V.C)

Rubber End Seal

Vinyl Sleeve

(P.V.C)

Dimensions : mm

Rubber End Seal

F 0.5

0.6

0.4Max.

15Min.

5Min.

D 0.5

15Min.

5Min.

D 0.5

7.5

10.0

0.8

Recommended Resources

Interface circuit between CMOS and PMOS d

Light emitting diode display circuit one c

Z-33 switching regulated power supply circuit

Male and female voice clarity circuit

555 electric fan intermittent power supply socket circuit

Memorable logic probe circuit

How long does it take to compile and generate a winCE under vs?: RT...; baobaoblueyi Embedded System

In STM8, TIM2, 3, and 4 are turned on at the same time, and the first interrupt time is inaccurate: void TIM2_INIT(void){TIM2_PSCR = 2; /*2-division to get 1MHZ timer clock, timer plus 1 is 1us*/TIM2_ARRH = 0x27; /*50ms interrupt once*/TIM2_ARRL = 0x10;TIM2_IER = 0x01; /*Update interrupt enable*/TIM...; lint001 stm32/stm8

opt3001 light sensor problem help: Using 51 MCU to simulate I2C timing to control opt3001 light sensor, the data captured by logic analyzer shows that opt3001 does not feedback ACK to MCU. What is the most likely problem in this case? ...; Kileo 51mcu

About the selection of pull-up and pull-down resistors at A and B ends of 485 bus: [size=4]Question: About RS485[/size] [size=4]Use a resistor to pull up[/size] [size=4]B uses a resistor to pull down[/size] [size=4]A and B are connected by resistors, [/size] [size=4]What are the app...; Jacktang Analogue and Mixed Signal

The first MicroPython book is about to be released: The first MicroPython book will be available on Amazon soon. sans-serif]This practical guide introduces programming with MicroPython on the open source hardware platform pyboard. The book explains ste...; dcexpert Robotics Development

6. [Learning LPC1768 library functions] Watchdog experiment: The purpose of the watchdog is to generate a reset when an error occurs in the microprocessor. When the watchdog is enabled, if the user does not feed the watchdog within the overflow period (reload t...; cxmdz NXP MCU

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components