For applications requiring improved electrical and
thermal performance at reduced cost, consider
DATEL’s new UCQ series “quarter brick” DC/DC
power converters. These compact units measure
just .45" x 2.3" x 0.4" (36.8 x 60.9 x 0.2 mm)
and fit the industry-standard footprint.
Available outputs range between .2V @ 40 Amps
to 5V @ 6.7 Amps and accept a wide input range.
The UCQ’s interleaved, synchronous-rectifier
topology offers high efficiency (up to 93%), tight
line and load regulation, low noise and fast step
response. A single-board optimized open-frame
design contributes to impressive thermal opera-
tion. UCQ’s will operate up to +70°C and 00 LFM
airflow with no derating.
The UCQ’s feature full isolation to 2250Vdc
meeting BASIC insulation requirements of
UL/EN/IEC 60950-. Input filters reduce propa-
gated switching noise back to input sources. Also
included is a remote On/Off switch control (with
positive or negative polarity), output trim adjustable
over nominal and output sense functions to reduce
power lead losses. Extensive protection items
avoid damage from out of limit voltages, currents
and temperatures. Protection faults automatically
recover using the hiccup technique. Besides safety
testing to 60950-, certifications for the UCQ
include application for EMC compliance (to FCC
class B), qualification testing (including HALT) and
CE marking.
+SENSE
(7)
+V
IN
(3)
+V
OUT
(8)
SWITCH
CONTROL
–V
OUT
(4)
–V
IN
(1)
–SENSE
(5)
PWM
CONTROLLER
OPTO
ISOLATION
REFERENCE &
ERROR AMP
V
OUT
TRIM
(6)
REMOTE
ON/OFF
CONTROL*
(2)
INPUT UNDERVOLTAGE, INPUT
OVERVOLTAGE, AND OUTPUT
OVERVOLTAGE COMPARATORS
* Can be ordered with positive (standard) or negative (optional) polarity.
Typical topology may vary between units.
Figure 1. Simplified Schematic
www.murata-ps.com
Technical enquiries
email: sales@murata-ps.com, tel:
+ 508 339 3000
MDC_UCQ Models.B02 Page of 7
Single Output UCQ Models
PRELIMINARY
Performance Specifications and Ordering Guide
➀
ORDERING GUIDE
Output
R/N (mVp-p)
Root Models
➀
UCQ-1.2/40-D24
UCQ-1.2/30-D48
UCQ-1.5/25-D48
UCQ-1.8/30-D48
UCQ-2.5/40-D24
UCQ-2.5/30-D48
UCQ-3.3/35-D24
UCQ-3.3/20-D48
UCQ-3.3/30-D48
UCQ-5/20-D24
UCQ-5/20-D48
UCQ-8/12-D24
UCQ-12/8.3-D48
UCQ-15/6.7-D24
V
out
I
out
Power
(Volts) (Amps) (Watts)
Typ.
Max.
Regulation (Max.)
➁
Line
Load
V
in
Nom.
(Volts)
Range
(Volts)
I
in
no
load (mA)
Input
I
in
full
load
(Amps)
Efficiency
Min.
Typ.
Low-Profile, Quarter Brick, 6.7-40 Amp
Isolated DC/DC Converters
.2
.2
.5
.8
2.5
2.5
3.3
3.3
3.3
5
5
8
2
5
40
30
25
30
40
30
35
20
30
20
20
2
8.3
6.7
48
36
37.5
54
00
75
5.5
66
99
00
00
96
99.6
00.5
TBD
50
50
00
80
50
30
50
50
50
35
TBD
00
TBD
TBD
00
80
TBD
20
00
50
80
80
60
55
TBD
50
50
TBD
±0.25%
±0.25%
±0.25%
±0.25%
±0.2%
±0.25%
±0.25%
±0.2%
±0.25%
±0.25%
±0.25%
±0.2%
±0.25%
TBD
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
24
48
48
48
24
48
24
48
48
24
48
24
48
24
8-36
36-75
36-75
36-75
8-36
36-75
8-36
36-75
36-75
8-36
36-75
8-36
36-75
8-36
TBD
30
50
45
20
50
30
50
50
60
80
TBD
80
00
TBD
0.90
0.94
.3
4.96
.80
5.4
.53
2.3
4.55
2.24
TBD
2.28
4.6
83%
8%
8%
83%
82%
85%
87%
88.5%
90%
88%
89%
88%
90%
9%
85%
83%
83%
86%
84%
87%
89%
90%
9%
9.5%
93%
9.5%
9%
92%
➀
These are partial model numbers. Please refer to the part number structure for complete ordering part numbers.
➁
All specifications are at nominal line voltage and full load, +25 deg.C unless otherwise noted. See detailed specifications. Output capacitors are µF ceramic || 0 µF electrolytic. I/O caps are necessary for
our test equipment and may not be needed for your application.
Outline dimensions:
2.3 × .45 × 0.39 inches
58.4 × 36.8 × 9.9 mm
Pinout: P32
(all models)
www.murata-ps.com
Technical enquiries
email: sales@murata-ps.com, tel:
+ 508 339 3000
MDC_UCQ Models.B02 Page 2 of 7
Single Output UCQ Models
PRELIMINARY
PART NUMBER STRUCTURE
Low-Profile, Quarter Brick, 6.7-40 Amp
Isolated DC/DC Converters
Output
Configuration:
Unipolar,
singular output
U CQ
-
3.3
/
35
-
D48 N B
H
-
C
RoHS Hazardous Materials
compliance
C
= RoHS-6 (no lead)
Y
= RoHS-5 (with lead)
Conformal coating
H
= Humiseal added (quantity order)
Blank
= no coating
Baseplate
B
=
Baseplate installed
Blank
=
No baseplate
On/Off Control Polarity
P
=
Positive polarity
N
=
Negative polarity
Quarter-Brick Package
Nominal Output Voltage
Maximum Rated Output :
Current in Amps
Input Voltage Range:
D24 = 18-36 Volts (24V nominal)
D48 = 36-75 Volts (48V nominal)
Note:
Note all model combinations
are available. Contact MPS.
MECHANICAL SPECIFICATIONS
UCQ with Optional Baseplate
Case C67
All dimensions are in inches (mm)
I/O Connections
Pin
2
3
4
Function P32
−Input
Remote On/Off*
+Input
−Output
Pin
5
6
7
8
Function P32
−Sense
Output Trim
+Sense
+Output
Component locations may vary between units.
* The Remote On/Off can be provided with either
positive (no suffix) or negative (“N” suffix) polarity.
Previously, Blue Eye Fox and wangjiafu1985 suggested that the forum should have a function to view new posts. This function was added today:As shown in the figure: Label 1 remains the same, including ...
The electrolytic capacitor is made of two strips of aluminum foil with insulating paper. Because it is wound, it is considered to be an inductor. This conclusion has been circulated for decades. I don...
Since I will be going to the company for internship in two months, the engineer from the relevant department of the company informed me that I should first familiarize myself with the wince system and...
I want to do something when COMBOBOX gets the focus. The method I used is if(GetFoucs()->GetDlgCtrlID==IDC_XXX), but the cursor is clearly on COMBOBOX but it doesn't seem to get the focus. The same co...
module count4(out,reset,clk);
output[3:0] out;
input[3:0] reset,clk;
reg[3:0] out;
always @(posedge clk)beginif(reset) out=0;else out=out+1;end
endmoduleIs the reason why out is defined as a register ...
My bsp contains stepldr and eboot, I want to run eboot, but after burning stepldr.nb1 into flash, dnw shows garbled characters! ! ! ! This is the initial code of the serial port: void Uart_Init(void) ...
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
This paper designs a dot matrix LED text display screen that is easy to update, expandable, and low-cost. The way to reduce costs is
① Use the Bluetooth data transmission function of mobile ph...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
Vertical cavity surface emitting lasers (VCSELs) are gradually replacing traditional edge emitting lasers, especially in low bandwidth and short-distance communication systems where cost factors ar...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
PV inverter manufacturer SMA has launched its first DC arc fault circuit interrupter (AFCI) PV inverter and has received UL certification.
The new SunnyBoy AFCI inverter models include 3000-US...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
Spatial Division Multiplexing (SDM) MIMO processing can significantly improve spectrum efficiency and thus greatly increase the capacity of wireless communication systems. Spatial Division Multip...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
LED light sources have many environmental advantages, but early products still have certain technical bottlenecks in heat dissipation and high brightness design that cannot be broken through....[Details]
Suggestions & Announcements
京公网安备 11010802033920号
EEWORLD
