3191EA473S7R5JNS1 datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> 3191EA473S7R5JNS1

3191EA473S7R5JNS1: DescriptionCAPACITOR, ALUMINUM ELECTROLYTIC, NON SOLID, POLARIZED, 7.5V, 47000uF, STUD MOUNT, CAN, ROHS COMPLIANT; CategoryPassive components capacitor; File Size362KB，4 Pages; ManufacturerCDE [ CORNELL DUBILIER ELECTRONICS ]; Environmental Compliance

Download Datasheet Parametric View All

3191EA473S7R5JNS1 Overview

CAPACITOR, ALUMINUM ELECTROLYTIC, NON SOLID, POLARIZED, 7.5V, 47000uF, STUD MOUNT, CAN, ROHS COMPLIANT

3191EA473S7R5JNS1 Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	CDE [ CORNELL DUBILIER ELECTRONICS ]
package instruction	,
Reach Compliance Code	compli
ECCN code	EAR99
capacitance	47000 µF
Capacitor type	ALUMINUM ELECTROLYTIC CAPACITOR
dielectric materials	ALUMINUM (WET)
ESR	7.3 mΩ
Manufacturer's serial number	3191
Installation features	STUD MOUNT
negative tolerance	10%
Number of terminals	2
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Package shape	CYLINDRICAL PACKAGE
polarity	POLARIZED
positive tolerance	30%
Rated (DC) voltage (URdc)	7.5 V
ripple current	15500 mA
surface mount	NO
Terminal shape	BINDING POST

Preview

Download Datasheet

View All

Type 3191

Aluminum Electrolytic, Screw Terminals, Switching and Audio Output

Screw Terminal Capacitors for Power Output Filtering

The low ESR of Type 3191 capacitors makes them

a great choice for output ﬁltering in switching and

audio power supplies. It’s available with the capacitor

element potted in place for lowest cost or secured by

rill, spoon shaped dimples in the side of the can. Rilled

construction offers high vibration and shock with-

standing and excellent heat transfer for higher ripple

current.

Outline Drawing

Highlights

•

Stud mount available

High current application

Industrial applications

Smoothing and ﬁltering

Audio power supplies

Speciﬁcations

Operating Temperature:

Rated Voltage:

Capacitance Range:

Capacitance Tolerance:

Ripple Current Multipliers

–40 to + 85 ºC

7.5 Vdc to 55 Vdc

2700 µF to 150000 µF

–10 to + 30%; –10 to +50%; ±20%

Ambient Temperature

Temperature

Multiplier

45 ºC

2.24

60 Hz

0.90

55 ºC

2.00

120 Hz

1.00

65 ºC

1.73

300 Hz

1.05

75 ºC

1.41

85 ºC

1.00

Frequency

Multiplier

1000 Hz

≥10

Khz

1.10

1.15

Life Test:

Shelf Life:

Vibration:

Complies with the EU Directive

2002/95/EC requirement restricting

the use of Lead (Pb), Mercury (Hg),

Cadmium (Cd), Hexavalent chromium

(Cr(VI)), PolyBrominated Biphenyls

(PBB) and PolyBrominated Diphenyl

Ethers (PBDE).

Endurance, 1500 h at rated voltage and 85 ºC

Δ Capacitance: ±10%

ESR ≤ 200% of limit

DCL ≤ 100% of limit

Storage, 500 h at 85 ºC

Δ Capacitance: ±10%

ESR ≤ 175% of limit

DCL ≤ 200% of limit

10 to 500 Hz, 0.75 mm or 10 g* if less,

3 directions, 2 h ea

Δ Capacitance: ±5%

no visible damage or leakage

*15 g if rilled construction

CDM Cornell Dubilier • 140 Technology Place. • Liberty, SC • 29657 • Phone: (864)843-2277 • Fax: (864)843-3800 • www.cde.com

Recommended Resources

Use CD4011 to make light-controlled flashing warning lights

Sending and receiving microphone (sensing) interface circuit

Frequency controlled switching power supply circuit diagram

Refrigerator protection circuit made with 8751

Circulating water control circuit

Is it the inverter or the integrator circuit?: As shown The input Uin of the op amp is obtained from the -380VDC bus through resistor voltage division to obtain -3.5VDC Is the op amp in the figure a simple inverting 1:1 amplifier circuit, or is it...; shaorc Analog electronics

How to configure uclinux to automatically obtain an ip after arm is powered on?: How to configure uclinux to let arm automatically get ip after power on? My development board is S3C44B0. I heard that uclinux supports dhcp. 1. What should I choose when compiling uclinux 2.4 kernel ...; wawj1819 Linux and Android

Can first-tier devices do the job?: Previously, the sensor head was made by Honeywell combined with first-line devices. The SHT21 may be smaller in size. The I2C interface direct cable transmission requires signal preprocessing. Can fir...; bjwl_6338 DIY/Open Source Hardware

linux-2.6.34 kernel porting documentation [simple operation]: I just transplanted the kernel image file, put it on the development board and ran it for a while, and the system is running!!! Pictures speak louder than words...See the attached documentation for th...; 37°男人 Embedded System

Introduction to the training for the 2013 Electronic Design Competition: [i=s] This post was last edited by paulhyde on 2014-9-15 03:11 [/i] Nanhua University Huang Zhiwei prepares for the 2013 Electronic Design Competition - Introduction to some information on training...; 黄智伟 Electronics Design Contest

Please tell me about the assembly instructions related to AVR program jump: I've been working on the assembly of AVR recently and encountered some problems. I'd like to ask enthusiastic netizens to help me figure out what's going on. The development board I have is atmega128a...; lr2131 Microchip MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components