EEWORLDEEWORLDEEWORLD

Part Number

Search

M83421/01-5007R

Description
Film Capacitor, Plastic, 400V, 0.25% +Tol, 0.25% -Tol, 0.0012uF, Through Hole Mount, AXIAL LEADED
CategoryPassive components    capacitor   
File Size294KB,29 Pages
ManufacturerDefense Logistics Agency
Download Datasheet Parametric View All

M83421/01-5007R Overview

Film Capacitor, Plastic, 400V, 0.25% +Tol, 0.25% -Tol, 0.0012uF, Through Hole Mount, AXIAL LEADED

M83421/01-5007R Parametric

Parameter NameAttribute value
MakerDefense Logistics Agency
package instruction,
Reach Compliance Codeunknow
ECCN codeEAR99
Other featuresRATED AC VOLTAGE (V): 100-240
capacitance0.0012 µF
Capacitor typeFILM CAPACITOR
dielectric materialsPLASTIC
Manufacturer's serial numberM83421/01
Installation featuresTHROUGH HOLE MOUNT
negative tolerance0.25%
Number of terminals2
Maximum operating temperature100 °C
Minimum operating temperature-65 °C
Package shapeTUBULAR PACKAGE
positive tolerance0.25%
Rated (DC) voltage (URdc)400 V
GuidelineMIL-PRF-83421/1D
surface mountNO
Terminal shapeWIRE
INCH-POUND
MIL-PRF-83421F
17 May 2017
SUPERSEDING
MIL-PRF-83421E
6 December 2010
PERFORMANCE SPECIFICATION
CAPACITOR, FIXED, METALLIZED PLASTIC FILM DIELECTRIC,
(DC, AC, OR DC AND AC), HERMETICALLY SEALED IN METAL CASES OR CERAMIC CASES,
ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
1. SCOPE
1.1 Scope. This specification covers the general requirements for established reliability (ER), metallized plastic
film dielectric, fixed capacitors, hermetically sealed in metal or ceramic cases. Capacitors covered by this
specification have failure rate levels (FRL) established in accordance with
MIL-STD-690.
The reliability for each level
is identified by a symbol in accordance with
table I.
These FRLs are established at a 90 percent confidence level and
maintained at a 10 percent producer's risk and, unless otherwise specified (see
3.1),
are based on life tests
performed at maximum rated voltage at maximum rated temperature. Unless otherwise specified (see
3.1),
an
acceleration factor of 5:1 has been used to relate life-test data obtained at 140 percent of rated voltage at maximum
rated temperature, to rated voltage at maximum rated temperature (see
6.1).
A part per million (PPM) quality system
is used for documenting and reporting the average outgoing quality of capacitors supplied to this specification.
Statistical process control (SPC) techniques are required in the manufacturing process to minimize variation in
production of capacitors supplied to the requirements of this specification.
1.2 Classification. Capacitors covered by this specification are classified by the style, as specified (see
3.1).
1.2.1 Part or Identifying Number (PIN). Capacitors specified herein (see
3.1)
are identified by a PIN which
consists of the basic number of the performance specification and a series of coded characters. The coded
characters provide information concerning the capacitors temperature coefficient, specification sheet number,
capacitance value, capacitance tolerance, voltage, case code, termination finish, and failure rate level. The PIN is in
the following form:
M83421/
01
-
1
123
M
Performance
specification
number
Specification sheet
number
(1.2.1.1)
Single digit
designating style
Nonsignificant
dash number
FRL
(1.2.1.2)
1.2.1.1 Dash. Use “-“ for standard product or “H” for random vibration option.
Comments, suggestions, or questions on this document should be addressed to DLA Land and Maritime, ATTN:
VAT, Post Office Box 3990, Columbus, OH 43218-3990, or emailed to
CapacitorFilter@dla.mil.
Since contact
information can change, you may want to verify the currency of this address information using the ASSIST Online
database at
https://assist.dla.mil/.
AMSC N/A
FSC 5910
Circuit Design of SEPIC Converter
Can anyone give me some information about the circuit design of SEPIC converter?...
bager_2000 Embedded System
Regarding proteus simulation, it should be considered a circuit problem
[i=s]This post was last edited by Demonstration Law on 2021-3-5 11:04[/i]I simulated the common anode connection of port p1 in proteus, and then connected p1.0 to the red light of the traffic light as...
示范法 51mcu
Can you please give me some advice on book selection?
I want to learn embedded systems, mainly for anti-theft door systems. But I don't know what kind of books I should choose to read!! Please give me some advice!...
yxj2046 Embedded System
cadence ic design teaching
Are there any teaching materials on cadence ic design in universities or companies?...
bmahu001 Analog electronics
Questions about OPT, NPO, VCM, etc. in Linear's official schematics
There are a few things I don't quite understand in Linear's official schematics. 1. Does the OPT (OPTION) at 1 in the figure require you to measure the appropriate parameters yourself or can you solde...
littleshrimp Analog electronics
Use the official SSD1306.py to drive OLED
[b][color=#ff0000]This content is originally created by EEWORLD forum user [size=3]dcexpert[/size]. If you want to reprint or use it for commercial purposes, you must obtain the author's consent and i...
dcexpert MicroPython Open Source section

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2144  2466  2272  1671  1771  44  50  46  34  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号