EEWORLDEEWORLDEEWORLD

Part Number

Search

BTL-54YECS-Y3-K

Description
Visible LED
CategoryLED optoelectronic/LED    photoelectric   
File Size225KB,3 Pages
ManufacturerDB Lectro Inc
Download Datasheet Parametric View All

BTL-54YECS-Y3-K Overview

Visible LED

BTL-54YECS-Y3-K Parametric

Parameter NameAttribute value
MakerDB Lectro Inc
Reach Compliance Codeunknow
MEGA BRIGHT LED
BTL-54YECS-XX-X
Product Features
Ultra Bright Yellow Color
High Light Output
Package Dimension
5X4mm Diameter Elliptical Package
Water Clear Lens
Highly Reliable
IC Compatible
Leads with Stand Off
Applications
Full Color Display
Automotive
Front Panel Indicator
Special Lighting
General Purpose LEDs
Tolerance:
±
inch
Unit:
mm
±
0.01
0.25
Optical and Electrical Characteristics at T
a
=25℃
Parameter
Luminous
Intensity
Viewing Angle
Dominant
Wavelength
DC Forward
Voltage
DC Reverse
Current
Symbol Minimum
I
v
2θ½
H-H
2θ½
V-V
585
0
Typical
600
70
30
590
1.9
Maximum
595
2.5
10
Units
mcd
deg
nm
V
µA
Conditions
I
F
= 20mA
(Note 1)
I
F
= 20mA
I
F
= 20mA
(Note 2)
λ
D
V
F
I
R
I
F
= 20mA
V
R
=5V
Notes:
1.
Light intensity measures the light sensing response standard using chromatic meter. Refer to the CIE
eye-response curve set by International Lighting committee.
Tolerance of minimum and maximum
intensity = ± 15%
2. Wavelength range can be selected from the bin selection table. Tolerance of minimum and
maximum = ± 2nm
3.
These products are sensitive to static electricity and care must be fully taken when handling
products
Page 1 of 3
LCD Data Collection
Recently I found a website on the Internet, which has a lot of LCD information. I know it is very useful for experts. I would like to share it with you. Address: http://www.amobbs.com/thread-1566201-1...
qui26 Microcontroller MCU
I hope everyone can help!
The semaphore created in ucgui is used to lock and unlock. So how is the semaphore created when the gui is initialized used in multiple tasks? (For example, will the semaphore used by the task that re...
kakalin Embedded System
Design of the inverting input summing circuit
How to add the signal source U1 and the signal source U2? How to build an adder circuit? As shown in the picture below, the reverse summing circuit of the two input terminals is shown to you. It can b...
bqgup Creative Market
[Raspberry Pi Pico Review] 1. Testing the Raspberry Pi Pico without soldering the pin headers and analyzing the Pico's power circuit
First of all, I would like to thank EE for giving me the opportunity to test the Raspberry Pi Pico . In this review, I will learn and share two major contents.1. Hardware part: Learn about Raspberry P...
tagetage DIY/Open Source Hardware
***Network card driver error: FEC: No PHY device found****
I started UCLINUX on coldfire5272 (without using the DEBUG program, downloading the kernel to FLASH, and then moving it to memory for execution). As a result, the above error occurred when the FEC dri...
paulhwun Embedded System
Please advise how to avoid the microcontroller from being burned out
[align=left][color=rgb(0, 0, 0)][font=sans-serif]Today I tested the wiring of a microcontroller. I connected two identical boards. After powering on, the power light on one board was normal, but the p...
hanwenli123 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2193  1028  2669  1772  1071  45  21  54  36  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号