EEWORLDEEWORLDEEWORLD

Part Number

Search

2207-38-LW-B

Description
Board Connector, 38 Contact(s), 2 Row(s), Female, Straight, 0.1 inch Pitch, Solder Terminal
CategoryThe connector    The connector   
File Size231KB,3 Pages
ManufacturerEaton
Download Datasheet Parametric View All

2207-38-LW-B Overview

Board Connector, 38 Contact(s), 2 Row(s), Female, Straight, 0.1 inch Pitch, Solder Terminal

2207-38-LW-B Parametric

Parameter NameAttribute value
MakerEaton
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPULL-OFF CARRIER
body width0.2 inch
subject depth0.165 inch
body length2.3 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedGOLD
Contact point genderFEMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact resistance10 mΩ
Contact styleRND PIN-SKT
Dielectric withstand voltage1000VAC V
maximum insertion force2.224 N
Insulation resistance10000000000 Ω
insulator materialPOLYTRIX
Manufacturer's serial numberLW
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature150 °C
Minimum operating temperature-60 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.128 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts38
Evacuation force-minimum value.834 N
I would like to ask an expert, I am new to STM8S103F2P6, I want to write a program that can directly operate IO, but I don't know how to set it...
I would like to ask an expert for help. I have just started using STM8S103F2P6 and want to write a program that can directly manipulate IO bits, but I don't know how to set it up....
bing_yu stm32/stm8
Patch welding method
[i=s] This post was last edited by paulhyde on 2014-9-15 03:32 [/i] How to solder a chip...
owlcjy Electronics Design Contest
[Comparison of solutions] + Design of 30V3A adjustable power supply using WEBENCH
For the purpose of the experiment, two power supplies were connected in series to test the circuit. One of the power supplies had a problem. When the output current was high, it suddenly decreased. I ...
dontium Analogue and Mixed Signal
XDS200U cannot connect to the development board. Testconnect always fails as shown below. Update dance is useless. Some friends have encountered...
[Start: Texas Instruments XDS2xx USB Emulator_0]Execute the command:%ccs_base%/common/uscif/dbgjtag -f %boarddatafile% -rv -o -S integrity[Result]-----[Print the board config pathname(s)]-------------...
alasijia DSP and ARM Processors
How do you calculate the input-output ratio of this circuit?
I want to see if mine is correct before submitting it....
西里古1992 Analog electronics
Two unused boards are available for exchange -- (already available)
[i=s] This post was last edited by zhang7309 on 2016-11-23 10:22 [/i] 1. MSP-EXP430FR5739 official introduction: [list] [*] Integrated MSP430FR5739: [list] [*] 16KB FRAM/1KB SRAM [*] 16-bit RISC archi...
zhang7309 Buy&Sell

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1818  1278  2610  266  807  37  26  53  6  17 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号