EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-MLPFA3005

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-MLPFA3005 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), FC/UPC Connector,

PH1-MLPFA3005 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codeunknow
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1537 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Try DE1-SoC
[i=s]This post was last edited by 574433742 on 2015-5-11 00:38[/i] [align=center][/align] [align=center][size=4][color=#0000ff]Figure 0-0: DE1-SoC[/color][/size][/align] [size=3] I have had the DE1-So...
574433742 FPGA/CPLD
How to use MSP430 hardware I2C - Taking BH1710 and AT24C02 as examples
Hardware I2CFinally, the controller was tuned. I have been hitting a dead end these days. In fact, the best reference is the one provided by TI . The code refers to the User's Guide and Application No...
fish001 Microcontroller MCU
What to do if there is no parallel port download cable!!!
I am using Zhou Ligong's EasyFPGA030, which only supports parallel port downloading. But I don't have a parallel port download cable, and neither does my laptop or my classmates! Do I have to spend te...
cobble1 FPGA/CPLD
Linux-2.6.18 kernel transplantation and root file system creation (simple)
linux-2.6.18 kernel transplantation and root file system creation (simple) 1. Go to http://www.kernel.org to download the kernel. The following takes linux-2.6.18.tar.bz2 as an example. ]# vi arch/arm...
donote Linux and Android
There are two codes. The first one shows 0, and the second one shows 8.
#include#define uint unsigned int #define uchar unsigned char sbit duan=P2^6; //Declare the latch end of U1 latch sbit wei=P2^7; //Declare the latch end of U2 latch void main() { wei=1; //Open U2 latc...
大赛 Embedded System
Modelsim SE added Altera library still not working
The problem is this: I added the Altera library to Modelsim SE and can see it. But when calling Modelsim SE for simulation in Quartus, the default library is still the work library, and a lot of Alter...
gddxz FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 668  765  205  1705  234  14  16  5  35  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号