HLMP-R100, HLMP-0301, HLMP-0401, HLMP-0504
2.5 mm x 7.6 mm Rectangular LED Lamps
Data Sheet
Description
The HLMP-R100, -0301, -0401, -0504 are solid state
lamps encapsulated in a radial lead rectangular epoxy
package. They utilize a tinted, diffused epoxy to
provide high on-off contrast and a flat high intensity
emitting surface. Borderless package design allows
creation of uninterrupted light emitting areas.
The HLMP-R100 uses a double heterojunction (DH)
absorbing substrate (AS) aluminum gallium arsenide
(AlGaAs) red LED chip in a light red epoxy package. This
combination produces outstanding light output over a
wide range of drive currents.
The HLMP-0301 has a high efficiency red GaAsP on
GaP LED chip in a light red epoxy package.
The HLMP-0401 provides a yellow GaAsP on GaP LED chip
in a yellow epoxy package.
The HLMP-0504 provides a green GaP LED chip in a green
epoxy package.
Features
•
Rectangular light emitting surface
•
Flat high sterance emitting surface
•
Stackable on 2.54 mm (0.100 inch) centers
•
Ideal as flush mounted panel indicators
•
Ideal for backlighting legends
•
Long life: solid state reliability
•
Choice of 4 bright colors
– DH AS AlGaAs Red
– High Efficiency Red
– Yellow
– High Performance Green
•
IC compatible/low current requirements
Package Dimensions
7.62 (0.300)
6.99 (0.275)
7.62 (0.300)
7.11 (0.280)
0.46 (0.018)
SQ. NOMINAL
2.54 (0.100)
NOMINAL
CATHODE LEAD
29.21 (1.15) MIN.
BOTTOM VIEW
8.00 (0.315)
7.37 (0.290)
1.27 (0.50)
NOMINAL
NOTES:
1. ALL DIMENSIONS ARE IN
MILLIMETERS (INCHES).
2. AN EPOXY MENISCUS MAY EXTEND
ABOUT 1 mm (0.040") DOWN THE LEADS.
3. THERE IS A MXIMUM 1° TAPER FROM
BASE TO THE TOP OF LAMP.
2.54 (0.100)
2.16 (0.085)
2.54 (0.100)
2.29 (0.090)
SIDE VIEW
Selection Guide
Luminous Intensity
Iv (mcd) at 20 mA
Color
DH AlGaAs Red
Red
Part Number
HLMP-R100
HLMP-R100-FG0xx
HLMP-0301
HLMP-0301-C00xx
HLMP-0301-DECxx
HLMP-0301-CD0xx
Min.
2.1
5.4
2.1
1.3
2.1
1.3
3.6
1.4
3.6
2.2
3.6
2.6
1.6
4.2
2.6
2.6
Typ.
–
17.2
–
–
6.8
4.2
–
–
–
7.2
11.4
–
–
13.4
8.4
–
Yellow
HLMP-0401
HLMP-0401-B00xx
HLMP-0401-D00xx
HLMP-0401-CD0xx
HLMP-0401-DEBxx
Green
HLMP-0504
HLMP-0504-B00xx
HLMP-0504-DECxx
HLMP-0504-CD0xx
HLMP-0504-C00xx
Part Numbering System
HLMP - x x xx - x x x xx
Mechanical Options
00: Bulk
01: Tape & Reel, Crimped Leads
02: Tape & Reel, Straight Leads
DD: Ammo Pack, Straight Leads
Color Bin Options
0: Full Color Bin Distribution
B: Color Bins 2 & 3 only
C: Color Bins 3 & 4 only
Maximum Iv Bin Options
0: Open (No Maximum Limit)
Others: Please refer to the Iv Bin Table
Minimum Iv Bin Options
Color Options
Please refer to the Iv Bin Table
1. As AlGaAs Red
3. High Efficiency Red
4. Yellow
5. Green
Package Options
2
R,0: Rectangular 2.5 mm x 7.6 mm
Absolute Maximum Ratings at T
A
= 25°C
Parameter
Peak Forward Current
Average Forward Current
[1]
DC Current
[2]
Power Dissipation
Reverse Voltage (I
R
= 100
μA)
Transient Forward Current
[3]
(10
μs
Pulse)
Operating Temperature Range
Storage Temperature Range
HLMP-R100
300
20
30
87
5
500
-20 to +100
-40 to +100
HLMP-0301
90
25
30
135
5
500
-40 to +100
-40 to +100
HLMP-0401
60
20
20
85
5
500
-40 to +100
-40 to +100
HLMP-0504
90
25
30
135
5
500
-20 to +100
-40 to +100
Units
mA
mA
mA
mW
V
mA
°C
Notes:
1. See Figure 5 to establish pulsed operating conditions.
2. For AlGaAs Red, Red, and Green Series derate linearly from 50°C at 0.5 mA/°C. For Yellow Series derate linearly from 50°C at 0.2 mA/°C.
3. The transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the LED die and
wirebond. It is not recommended that the device be operated at peak current beyond the peak forward current listed in the Absolute Maximum
Ratings.
3
Electrical/Optical Characteristics at T
A
= 25°C
HLMP-R100
Sym.
2q
1/2
HLMP-0301
100
HLMP-0401
100
HLMP-0504
100
Deg.
Description
Included Angle
Between Half
Luminous
Intensity Points
Peak Wavelength
Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Units
100
Test
Conditions
Note 1.
Fig. 6
l
P
645
635
583
565
nm
Measure-
ment at
Peak
Note 2.
l
d
Dl
1/2
t
s
C
Rq
J-PIN
Dominant
Wavelength
Spectral Line
Halfwidth
Speed of Response
Capacitance
Thermal Resistance
637
20
30
30
260
626
40
90
16
260
585
36
90
18
260
569
28
500
18
260
nm
nm
ns
pF
°C/W
V
F
= 0;
f = 1 MHz
Junction
to Cathode
Lead
I
F
= 20 mA
Figure 2.
I
R
= 100
μA
Note 3.
V
F
V
R
h
v
Forward Voltage
Reverse Breakdown
Voltage
Luminous Efficacy
5.0
1.8
2.2
5.0
1.9
2.6
5.0
2.1
2.6
5.0
2.2
3.0
V
V
80
145
500
595
lm/W
Notes:
1.
q
1/2
is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
2. The dominant wavelength,
l
d
, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the
device.
3. Radiant intensity, I
e
, in watts/steradian, may be found from the equation I
e
= I
v
/h
v
, where I
v
is the luminous intensity in candelas and
h
v
is the
luminous efficacy in lumens/watt.
1.0
AlGaAs RED
GREEN
RELATIVE INTENSITY
T
A
= 25° C
0.5
YELLOW
HIGH EFFICIENCY RED
0
500
550
600
650
WAVELENGTH – nm
700
750
Figure 1. Relative intensity vs. wavelength.
4
90
80
I
F
– FORWARD CURRENT – mA
70
60
50
40
30
20
10
0
1.0
2.0
HER
AlGaAs
RED
2.5
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 20 mA)
2.0
HER, YELLOW, GREEN
1.3
1.2
η
PEAK
– RELATIVE EFFICIENCY
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0
10
20
YELLOW
HER
GREEN
1.5
1.0
0.5
0
YELLOW
AlGaAs RED
AlGaAs RED
GREEN
3.0
4.0
5.0
0
5
10
15
20
25
30
30 40
50
60
70
80
90
V
F
– FORWARD VOLTAGE – V
I
DC
– DC CURRENT PER LED – mA
I
PEAK
– PEAK CURRENT PER LED – mA
Figure 2. Forward current vs. forward voltage.
V
F
(300 mA) for AlGaAs Red = 2.6 volts typical.
Figure 3. Relative luminous intensity vs. forward
current.
Figure 4. Relative efficiency (luminous intensity
per unit current) vs. peak current.
h
v
(300 mA) for
AlGaAs Red = 0.7.
I
PEAK
MAX. RATIO OF MAXIMUM PEAK CURRENT
TO TEMPERATURE DERATED
I
DC
MAX.
MAXIMUM DC CURRENT
RATIO OF MAXIMUM TOLERABLE
PEAK CURRENT TO MAXIMUM
TOLERABLE DC CURRENT
4.0
3.0
10
9
8
7
6
5
4
3
2
10 K
ESH
EFR
f–R
z
100 H
z
300 H
H
100 K
z
z
10 KH
z
30 KH
3 KH
z
1 KH
z
E
RAT
– 10
2.0
1.5
0 Hz
I
PEAK
MAX.
I
DC
MAX.
1 KH
3 KH
z
300
Hz
Hz
z
1.0
1
10
100
1000
10,000
1
1
10
100
1000
10000
t
P
– PULSE DURATION –
µs
HER, ORANGE, YELLOW, and GREEN
t
p
– PULSE DURATION –
µs
AlGaAs RED
Figure 5. Maximum tolerable peak current vs. peak duration (I
PEAK
MAX determined from temperature derated I
DC
MAX).
20°
30°
40°
50°
60°
70°
80°
90°
10°
0°
1.0
0.8
0.6
0.4
0.2
10° 20° 30° 40° 50° 60° 70° 80° 90° 100°
Figure 6. Relative luminous intensity vs. angular displacement.
5
京公网安备 11010802033920号
EEWORLD
