EEWORLDEEWORLDEEWORLD

Part Number

Search

230D1Z474J

Description
Film Capacitor, Polyester, 35V, 5% +Tol, 5% -Tol, 0.47uF,
CategoryPassive components    capacitor   
File Size375KB,12 Pages
ManufacturerSeacor Capacitors
Download Datasheet Parametric View All

230D1Z474J Overview

Film Capacitor, Polyester, 35V, 5% +Tol, 5% -Tol, 0.47uF,

230D1Z474J Parametric

Parameter NameAttribute value
MakerSeacor Capacitors
package instruction,
Reach Compliance Codeunknow
ECCN codeEAR99
capacitance0.47 µF
Capacitor typeFILM CAPACITOR
Custom functionsFor Dimensions Please Consult Factory
dielectric materialsPOLYESTER
negative tolerance5%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package formAxial
positive tolerance5%
Rated (DC) voltage (URdc)35 V
series230D(35 VOLT)
®
METALLIZED POLYESTER CAPACITORS
230 SERIES
leads are available.
Protective clear wrap is offered on
all wrap and fill units. Please add
.010” to maximum T and W dimen-
sion for protective clear wrap.
The potting material and endfills
of Electrocube’s capacitors meet or
exceed the flammability requirements
of UL94VO.
Dimensional variations for all
MFD values are available with the
same volume to meet your design
requirements.
The unique high performance and
long life characteristics of polyester
account for the varied applications of
this miniature capacitor series. A wide
range of sizes and configurations are
available. You can choose from axial-
lead wrap and fill, oval and round
shapes and rectangular epoxy case
with axial and radial leads.
These capacitors feature extended
foil construction and standard tin-
coated copper-clad steel leads. Nickel,
copper, dumet and other special
SPECIFICATIONS
Temperature:
-55°C to +85°C at rated voltage; to +125°C
with 50% voltage derating.
TYPICAL DIELECTRIC CHARACTERISTIC CURVES
and 25°C for a period not to exceed 1 minute; current limited
to 5 mA.
Life Test:
Will withstand rated voltage for 250 hrs. at +125°C
with not more than 1 failure in 12 permitted.
Dissipation Factor:
Shall not exceed 1.0% at 25°C.
Dielectric Absorption:
Shall not exceed 0.5% at 25°C per
MIL-C-19978.
Acceptance Criteria:
Measurement frequency for capacitance
Insulation Resistance:
At rated voltage or 500V, whichever
is less, units shall meet the minimum values below:
NOTES:
For information regarding insulating sleeves, mountings, special terminals,
non-standard leads, circuit connections and other hardware, please
consult factory.
For styles and ratings not shown, or for unusual requirements necessitated
by special circuit applications (including higher IR or lower DF), consult
the factory direct.
All Electrocube film capacitors have endfills and tape that
meet or exceed the flammability requirements of UL94V0.
®
1307 S. Myrtle Ave. • Monrovia, CA 91016 • TEL: (626) 301-0122 • FAX: (626) 357-8099
e-mail: sales@electrocube.com • Internet: www.electrocube.com • (IR: 9/99)
INSULATION RESISTANCE
(MEGOHMS TIMES MICROFARADS)
% DISSIPATION FACTOR
and dissipation factor shall be 1000 Hz for values up to 1 mfd
and 120 Hz for values of 1.0 mfd and up.
% CAPACITANCE CHANGE
Dielectric Strength:
Will withstand 150% at rated voltage
STM32L0 LL library IIC configuration and usage issues, can't send the data I want. Ask for advice
The FW version is 1.12;the IC used is STM32L0F4U;CUBEMX configuration, using LL library.Prerequisite: Because the IIC of the slave is a non-standard protocol, the first byte is not to control R/W, and...
麻袋 stm32/stm8
[Nucleo-F413ZH Review] 2 Development Board Review_How to quickly create a new project, the difference between Keil and Cube
[i=s] This post was last edited by Xianjing on 2016-12-29 09:10 [/i] It has been a while since I got the board. I have been busy with the project recently, so I can only take time to play with it at n...
仙景 stm32/stm8
Two ways to avoid self-oscillation
I just found two methods to reduce self-oscillation: 1. Main pole correction method: A relatively simple and commonly used correction measure is to connect a capacitor at an appropriate position in th...
loadinghl Electronics Design Contest
I heard that the brake failure of previous Toyota cars was caused by a minor code error.
[color=#000][font=Arial, Helvetica, sans-serif, 瀹嬩綋][size=12px]In 2007, a Toyota car lost control and failed to brake on a US highway, causing a car accident. This incident later became a sensation an...
wangfuchong Talking
Precision voltage source + DDS AC signal source PCB (99se)
Precision voltage source + DDS AC signal source PCB (99se) [color=#000][font=Helvetica, Arial, sans-serif]Continuation of ADI DIY activities and Renesas DIY activities[/font][/color]...
蓝雨夜 ADI Reference Circuit
Shandong Province 2010 Electronic Design Competition Group, join us now, let's discuss!!!
[i=s]This post was last edited by paulhyde on 2014-9-15 08:54[/i]Shandong Province 2010 Electronic Design Competition Group, please join us and discuss!!! 116389549 Shandong Province 2010 Electronic D...
kllkko Electronics Design Contest

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 264  1290  1172  1361  153  6  26  24  28  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号