EEWORLDEEWORLDEEWORLD

Part Number

Search

232A1B272J

Description
Film Capacitor, Polyester, 100V, 5% +Tol, 5% -Tol, 0.0027uF, 4218,
CategoryPassive components    capacitor   
File Size375KB,12 Pages
ManufacturerSeacor Capacitors
Download Datasheet Parametric View All

232A1B272J Overview

Film Capacitor, Polyester, 100V, 5% +Tol, 5% -Tol, 0.0027uF, 4218,

232A1B272J Parametric

Parameter NameAttribute value
MakerSeacor Capacitors
package instruction, 4218
Reach Compliance Codeunknow
ECCN codeEAR99
capacitance0.0027 µF
Capacitor typeFILM CAPACITOR
dielectric materialsPOLYESTER
high7.62 mm
length10.668 mm
negative tolerance5%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package formRadial
positive tolerance5%
Rated (DC) voltage (URdc)100 V
series232A(100 VOLT)
size code4218
Terminal pitch7.62 mm
width4.572 mm
®
METALLIZED POLYESTER CAPACITORS
230 SERIES
leads are available.
Protective clear wrap is offered on
all wrap and fill units. Please add
.010” to maximum T and W dimen-
sion for protective clear wrap.
The potting material and endfills
of Electrocube’s capacitors meet or
exceed the flammability requirements
of UL94VO.
Dimensional variations for all
MFD values are available with the
same volume to meet your design
requirements.
The unique high performance and
long life characteristics of polyester
account for the varied applications of
this miniature capacitor series. A wide
range of sizes and configurations are
available. You can choose from axial-
lead wrap and fill, oval and round
shapes and rectangular epoxy case
with axial and radial leads.
These capacitors feature extended
foil construction and standard tin-
coated copper-clad steel leads. Nickel,
copper, dumet and other special
SPECIFICATIONS
Temperature:
-55°C to +85°C at rated voltage; to +125°C
with 50% voltage derating.
TYPICAL DIELECTRIC CHARACTERISTIC CURVES
and 25°C for a period not to exceed 1 minute; current limited
to 5 mA.
Life Test:
Will withstand rated voltage for 250 hrs. at +125°C
with not more than 1 failure in 12 permitted.
Dissipation Factor:
Shall not exceed 1.0% at 25°C.
Dielectric Absorption:
Shall not exceed 0.5% at 25°C per
MIL-C-19978.
Acceptance Criteria:
Measurement frequency for capacitance
Insulation Resistance:
At rated voltage or 500V, whichever
is less, units shall meet the minimum values below:
NOTES:
For information regarding insulating sleeves, mountings, special terminals,
non-standard leads, circuit connections and other hardware, please
consult factory.
For styles and ratings not shown, or for unusual requirements necessitated
by special circuit applications (including higher IR or lower DF), consult
the factory direct.
All Electrocube film capacitors have endfills and tape that
meet or exceed the flammability requirements of UL94V0.
®
1307 S. Myrtle Ave. • Monrovia, CA 91016 • TEL: (626) 301-0122 • FAX: (626) 357-8099
e-mail: sales@electrocube.com • Internet: www.electrocube.com • (IR: 9/99)
INSULATION RESISTANCE
(MEGOHMS TIMES MICROFARADS)
% DISSIPATION FACTOR
and dissipation factor shall be 1000 Hz for values up to 1 mfd
and 120 Hz for values of 1.0 mfd and up.
% CAPACITANCE CHANGE
Dielectric Strength:
Will withstand 150% at rated voltage
What new programmable counter chips are available?
Are old counters like 8253 and 68040 still in use? Are there any counters with smaller packages or multiple channels? Serial control is even better....
coldra Embedded System
I would like to ask if two 16-bit SDRAMs can form a 32-bit memory. Now only the address line and data line of a single SDRAM are equal in length, not the length of the two SDRAMs. Will this have any impact?
I want SDRAM to run at the highest frequency of 133MHz. First piece. Addr Bus: prop delay: from U1001.E9 to U4001.G1 min=18 MM max=23 MM Data Bus (Data0~Data15): (RDly) U1001.D12 to U4001.A8 min= 15.6...
hjacky Embedded System
I am looking for a solution to automatically run programs when the MC1000 is turned on (the cold start settings must not be lost)!
I have recently been working on a small project for a handheld device, the device is MC1000 (barcode data collector), the platform is Wince 4.2, and the development tool is vs2003. Now I have realized...
seawave2000 Embedded System
Invite you to join Microchip's online seminar - Designing energy-efficient solutions for your IoT sensors
Microchip will host a webinar on Tuesday, June 29, titled “Designing Energy-Efficient Solutions for Your IoT Sensors.”When designing a battery-powered application, one of the most difficult tasks is t...
eric_wang Sensor
FPGA-based CPU design
...
至芯科技FPGA大牛 FPGA/CPLD
How many slave devices can a master device connect to under the Bluetooth 5.0 protocol?
How many slave devices can a master device connect to under the Bluetooth 5.0 protocol?...
une001 RF/Wirelessly

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2205  55  2870  2681  1188  45  2  58  54  24 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号