The Medallion 2100 Optical A/B Switch is a high-performance solution for network
protection and optical redundancy. Packaged in convenient 1 RU housing, this line of
optical switches provides an automatic or manual fiber switching function to protect the
network from inadvertent service outages due to up-stream optical signal degradation.
Each fiber’s optical signal power level is continuously monitored, as is an adjustable
optical trip threshold for each channel. If the primary fiber’s optical signal power level
falls below the desired optical trip threshold, the unit automatically switches to the
secondary fiber, thus eliminating the need for intervention of a system operator. The
Medallion 2100 is capable of manual switching or can be switched remotely via SNMP
or via a WEB browser adding optical protection to many system applications.
The Medallion 2100 series is designed as a low power, cost-effective, high-
performance switching solution for applications that demand reliable and rapid
response to changing network conditions.
Features
Automatic, Manual and Remote
Switching
Up to 4 Independent Switches
Auto-Switching Time Less than 10 ms
SNMPv2 Control Interface
Web Server
Front Panel LED Indicators
1 RU Rack-Mount Enclosure with Choice
of Dual Hot Swappable AC or DC
Redundant Power Supplies
Example Redundant Path Configuration for CATV Broadcast
Medallion 6000
RF In
CATV Tx (Main)
MAIN
Medallion 2100
Optical Switch
BACKUP
Medallion 7100/7200
EDFA
…
To WDM & PONs
RF In
Medallion 6000
CATV Tx (Backup)
Optical Characteristics
Property
Operating Wavelength
Insertion Loss
Return Loss
Polarization Dependent Loss
Repeatability
Cross Talk
Input Optical Power
Switching Time
Durability
Min.
1260
-
-
-
-
-
-
-
-
Typ.
≤
1.0
≥
50
≤
0.05
+/-0.02
≥
55
-
≤
10
≥
10
7
Max.
1620
1.5
-
0.1
+/-0.03
-
27
25
-
Units
nm
dB
dB
dB
dB
dB
dBm
ms
Cycles
| REV 2015.06
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Medallion 2100 Optical A/B Switch
DATASHEET | JUNE 2015
FIBER OPTICS
General and Mechanical Specifications
Property
Switching Threshold
Switching Mode
Optical Connector
Monitoring Interfaces
Operating Temperature
Storage Temperature
Power Consumption
Supply Range (VAC)
(VDC)
Dimensions
Individual Switches per Rack Unit
Requirement
20 dB dynamic range – see ordering info
Auto, Manual, Remote
SC/APC
100 Base-T Ethernet
Rear Panel RS-232 interface
Front Panel Indicators
0°C to 50°C
-25°C to 65°C
15 W
85 to 240 VAC, 50/60 Hz
36 - 72 VDC
430 mm x 300 mm x 44 mm
Up to 4
EN50083-2-2006
EN 55013
EN 61000-3-2
EN 61000-4-6
EN 61000-4-3
EN 61000-4-2
EN 61000-4-4
EN 61000-3-3
FCC Part 15 (Subpart B, Class A), 107(b), 109(b)
IEC 60950-1/A1:2009
GR-2853-CORE
GR-2853-CORE
0% to 95%
Comments
Settable within range
Other styles available (see ordering information)
SNMPv2, WEB Graphical User Interface
Local Craft Interface
LED and Vacuum Fluorescent Display
Maximum
Agency Listings, EMI
Agency Listing, Safety
Transportation Vibration
Transportation Shock
Relative Humidity (non-condensing)
European Union “RoHS 2 Directive” Compliance
All homogenous materials contained in the product contain less than the maximum concentration levels for lead, mercury,
cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers permitted under the European
Union Directive 2011/65/EC (the “RoHS 2 Directive”)
| REV 2015.06
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Medallion 2100 Optical A/B Switch
DATASHEET | JUNE 2015
FIBER OPTICS
Outline Drawing
| REV 2015.06
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Medallion 2100 Optical A/B Switch
DATASHEET | JUNE 2015
FIBER OPTICS
Model Number Information (note 1)
2100 –
Logo &
Customer
Specific
0-EMCORE
logo
1-no
logo
Operating
Wavelength
0
- 1260 nm
to 1620 nm
–
Switch
Configuration
12 -
1 out, 2 in
13 -
1 out, 3 in
14 -
1 out, 4 in
1X -
1 out, X in
Switch
Quantity
01
– 1 switch
02
– 2
switches
03
– 3
switches
04
– 4
switches
0X
– X
switches
–
Optics
1-
SC/APC
2-
FC/APC
3-
E2000
Optical
Connection
1-
Front Mount
2-
Rear Mount
1
Switching
Threshold Range
1
–
(-20 dBm, +20 dBm)
Reserved
0
Power Supply
1 -
AC primary,
no secondary
2 -
DC primary,
no secondary
3 -
AC primary,
AC secondary
4 -
AC primary,
DC secondary
5 -
DC primary,
DC secondary
Note 1: Not all configurations are available - contact factory
Example: 2100-10-1204-11103 No logo, 1550 nm, 1 x 2 switch, 4 switches, SC/APC connectors, front mount connectors, -20
dBm to +20 dBm range, AC power supply primary, AC power supply secondary
| REV 2015.06
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Recently, I checked the information of both. I found that OpenGL ES is very popular because it supports many platforms and has good versatility. Of course, the performance is also very good. I wrote a...
Recently, my teacher asked me to develop a touch screen driver under vxworks on an arm9 board. I wonder if anyone has the relevant driver code for reference! It doesn't matter how much it is! Or if an...
When I use the JTAG tool on my F149, the Security fuse ××own appears again. I am so depressed.This is the most frightening thing when making F149.Basically, a whole chip has to be scrapped.I am so dep...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
LED lamps and bulbs are now rapidly replacing incandescent, halogen and CFL (compact fluorescent lamp) light sources in many general lighting applications. Flyback DC/DC converters are the power su...[Details]
With the advocacy and implementation of the government's Safe City Plan, the security market has increasingly higher requirements for the clarity of surveillance images. Imagine that after a case o...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
Introduction
Nowadays, people pay more and more attention to the security alarm system, and people have higher and higher requirements for the functions and performance of the alarm. This paper prop...[Details]
At present, how various communication technologies will evolve after 3G is a focus of great concern in the industry. Especially for TD-SCDMA, whether it can achieve smooth evolution to the next gen...[Details]
Nowadays, more and more people have digital cameras. The convenience and speed of digital cameras have gradually replaced film cameras and become the main tool for people's daily photography. The n...[Details]
In order to prevent the lithium battery from being damaged by abnormal conditions such as overcharge, over discharge, and overcurrent, a lithium battery protection device is usually used to prevent...[Details]
Power supply is often the most easily overlooked link in the circuit design process. In fact, as an excellent design, power supply design should be very important, which greatly affects the perfor...[Details]
The overall operating performance of an electric car depends first on its battery system and motor drive system. The drive system of an electric car is generally composed of three main parts: a con...[Details]
DigRF
is
poised to replace the two main forms of data communication paths between RF and baseband semiconductor devices:
analog
signaling, and proprietary digital signaling (paralle...[Details]
Designing low power circuits while achieving acceptable performance is a difficult task. Doing so in
the RF
bands increases the challenge dramatically. Today, nearly everything has wireless...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
