(5 ±1 seconds and charge/discharge not exceeding 50 mA)
0.1%
1,000 megohm microfarads or 100 GΩ
(Rated voltage applied for 120 ±5 seconds @ 25°C)
Parameters/Characteristics
To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.
Capacitance and dissipation factor (DF) measured under the following conditions:
1 MHz ±100 kHz and 1.0 Vrms ±0.2 V if capacitance ≤ 1,000 pF
1 kHz ±50 Hz and 1.0 Vrms ±0.2 V if capacitance > 1,000 pF
Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as
Automatic Level Control (ALC). The ALC feature should be switched to "ON."
Post Environmental Limits
High Temperature Life, Biased Humidity, Moisture Resistance
KEMET reserves the right to substitute product with an improved temperature characteristic, tighter capacitance tolerance and/or higher voltage capability within
the same form factor (configuration and dimensions).
These products are protected under US Patents 7,172,985 & 7,670,981, other patents pending, and any foreign counterparts.
KEMET reserves the right to substitute product with an improved temperature characteristic, tighter capacitance tolerance and/or higher voltage capability within
the same form factor (configuration and dimensions).
These products are protected under US Patents 7,172,985 & 7,670,981, other patents pending, and any foreign counterparts.
When I was browsing TI's Android mobile app yesterday, I found this Chinese user guide that appeared quietly. It is no longer a pseudo-Chinese document with only the first one in Chinese. It seems to ...
[img]http://www.xinlegou.com/admin/editubb/UploadFile/201041010408548.jpg[/img]As the title says, after I connected according to the circuit diagram below, the output is always high level. I tried to ...
By default, uclinux uses the serial port to print information. Now I want this serial port to do other things. How can I turn off the serial port printing from the kernel?...
1. Board OverviewThe dual-receive and dual-transmit radio RF board based on XC7Z100+ADRV9009 is a special function board developed based on Xilinx ZYNQ FPGA and ADI's wireless transceiver chip ADRV900...
How can I select DSP and HPIC HPIA HPID through PCI2040? Which specific PCI register should be operated to achieve these goals? I didn't see a clear explanation on the Internet. The document said that...
Pulse oximeters, non-invasive instruments used to monitor a patient's blood oxygen saturation, are benefiting from moving away from expensive discrete component solutions toward more integrated design...[Details]
Designers of hearing aids have stringent requirements. Hearing aids must be small enough to fit in or behind the ear, operate on ultra-low power, and be free of noise or distortion. To meet these requ...[Details]
Keeping the heart environment compact and warm is beneficial in most cases, but it’s another story for electronic heart scanners. When GE Healthcare was designing a scanner that was said to be the fas...[Details]
As the price of readers and tags decreases and the global market expands, the application of radio frequency identification (RFID) is increasing day by day. Tags can be powered by readers (passive ...[Details]
As the whole equipment is becoming increasingly miniaturized and power-saving, low-dropout linear regulators (LDOs) with low power consumption are becoming the mainstream in the market for linear regu...[Details]
Broadband services supporting triple play voice, video and data are evolving for first mile customers (small businesses and homes). A key factor in this FTTx evolution is GPON (Gigabit Passive Opti...[Details]
This article will discuss a common problem in wireless mobile data reception.
Problems facing RF receivers
The common problem faced by RF receivers is that the same hardware must be used ...[Details]
With the continuous emergence of new technologies and the increasing complexity of DSP real-time systems, there are more and more different types of external devices. Writing drivers for these exte...[Details]
Introduction
Wireless operators are driving demand for broadband and data rates by offering enhanced data services to increase average revenue per user (ARPU). The need to provide users with ...[Details]
AD604 is a product of Analog Devices (AD). Compared with similar products, AD604 has the characteristics of ultra-low noise, high precision, continuously adjustable gain, and the decibel (dB...[Details]
Abstract This paper
introduces a wireless radio frequency transmission chip nRF9E5 based on 8051 core. The remote control system of flapping-wing micro-aircraft is made by using this chip. Th...[Details]
Abstract: CC2420 is a 2.4GHz RF chip introduced by Chipcon that complies with the IEEE 802.15.4 specification. It is used to develop ZigBee devices and products for PAN networks such as industrial ...[Details]
With the improvement of people's requirements for vehicle riding comfort and the development of passenger car suspension technology in my country, air suspension is increasingly used in passenger ...[Details]
Preface
In the application of PLL, DLL and CDR circuits, people generally require the output clock signal to have a 50% duty cycle so that data can be sampled at both the rising and fallin...[Details]
For mobile phone products, using low-cost components in design is only the first step to make the price competitive. The cost of the production process, especially the cost incurred during the fina...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
