EEWORLDEEWORLDEEWORLD

Part Number

Search

HBSTC-107-S-XXX-20-GT-200-LT

Description
Board Connector, 7 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Receptacle
CategoryThe connector    The connector   
File Size133KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

HBSTC-107-S-XXX-20-GT-200-LT Overview

Board Connector, 7 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Receptacle

HBSTC-107-S-XXX-20-GT-200-LT Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerMajor League Electronics
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresLEAD STYLE=0.730\",HIGH TEMP.
body width0.1 inch
subject depth0.2 inch
body length0.7 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (10) OVER NICKEL (50)
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial numberBSTC
Plug contact pitch0.1 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature250 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness10u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.055 inch
Terminal pitch2.54 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts7
About where data is stored
There is a paragraph in the DMA routine in the book "STM32 Processor Development and Application Based on MDK" that I cannot understand. It is as follows: In order to make the source data in FLASH and...
juntianya stm32/stm8
Urgent! How to read files in Win CE through PC software in C#!
After Win CE is connected to PC via USB, I want to directly read files in Win CE through PC-side software written in C#. How can I do this?...
wow Embedded System
When using C6000, the corresponding routine of MCSDK is imported and compiled, why does it fail?
I use C6000, and import the corresponding routines from MCSDK, but the compilation fails. What's the problem?...
娃娃7 DSP and ARM Processors
Published in "Electrician Forum" In the TN-S system, is it necessary to do repeated grounding after entering the building?
In the TN-S system, a three-phase five-wire cable is introduced from the outside into the building. Because the building has a total equipotential connection, the cable is grounded again after it is i...
aone2008 Industrial Control Electronics
When choosing an oscilloscope, bandwidth is generally considered. When should sampling rate be considered?
When choosing an oscilloscope, bandwidth is generally considered. When should sampling rate be considered?...
小艾 Test/Measurement
Running a wince system on an arm9-based development board, read and write bus issues
A development board based on arm9 (EP9302) runs a wince system, and there is a problem with the read and write bus: I wrote a small test program on wince, which reads the value of a virtual address (D...
shxjzwldx Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 231  2194  1  2195  2589  5  45  1  53  58 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号