EEWORLDEEWORLDEEWORLD

Part Number

Search

54111-410-18-1950

Description
Board Connector, 18 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size63KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54111-410-18-1950 Overview

Board Connector, 18 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54111-410-18-1950 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerAmphenol
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.094 inch
subject depth0.768 inch
body length1.8 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN-PB ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number54111
Plug contact pitch0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.095 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts18
PDM: Rev:E
STATUS:
Released
Printed: Jun 03, 2008
.
I/O parallel port directly drives LED display
1.Experimental TasksAs shown in the figure below, P0.0 - P0.7 of the P0 port of the AT89S51 microcontroller are connected to the a - h segments of a common cathode digital tube , and the common end of...
rain MCU
Question about falling edge triggering
I want to make a program for a single-chip microcomputer to control a stepper motor. The following is only a part of the program. I have an idea, but there are still problems in the implementation of ...
ZNF 51mcu
430 Why is it so quiet?
......
huo_hu Microcontroller MCU
How to synchronize the signals from two sources
I made a reverse addition circuit in an analog electronics book. I want to synchronize the signals from the two signal sources. For example, they are all 100HZ, with a peak-to-peak value of 100mv, and...
笑溜溜 Analog electronics
Protel99出现“Access violation at address 40067324 in module 'Vcl50.bpl'.
When using Protel99 to open a PCB diagram, "Access violation at address 40067324 in module 'Vcl50.bpl'. Write of address 0000014C" appears. How can I solve this problem?...
qinyucheng PCB Design
Case! EMI rectification of power supply
[i=s]This post was last edited by qwqwqw2088 on 2019-5-28 09:21[/i] [size=4]This is a power supply with a wide input voltage of 120-277V 60HZ, an output of 48V, 273mA, and a Buck topology. Note: In th...
qwqwqw2088 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2225  2844  2507  2570  2159  45  58  51  52  44 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号