EEWORLDEEWORLDEEWORLD

Part Number

Search

3559P12KD0

Description
Board Connector, 12 Contact(s), 3 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size203KB,2 Pages
ManufacturerLeoco USA Corp
Websitehttp://www.leoco.com.tw
Download Datasheet Parametric View All

3559P12KD0 Overview

Board Connector, 12 Contact(s), 3 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

3559P12KD0 Parametric

Parameter NameAttribute value
MakerLeoco USA Corp
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresMATING PIN LENGTH=0.231 INCH
body width0.1 inch
body length0.4 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact point genderMALE
contact modeRECTANGULAR
Contact resistance40 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage500VAC V
Insulation resistance500000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
Manufacturer's serial number3559
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number3
Number of rows loaded3
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts12
Everyone has gone home, but I haven’t. How about you?
:kiss::kiss::kiss::puzzle:I'm about to go home, and I'm so anxious waiting. Is there anyone who feels the same as me?...
499362154 Talking
MCU LCD driver problem with HD66781 driver chip
Hello everyone, this wide screen just can't output any data on our system. Has anyone adjusted this screen before? Please help me. The initialization code is: void Mcupanel_PowerOnInit(void) { int i,j...
sunyitui Embedded System
I would like to ask a question about how to use interrupt mode to send data in UART1 of stm8s103K3
I now follow the routine, and configure CR2=0x08, CR1=0, CR3=0, BRR2=0X68, BRR1=0X02 (9600 baud rate) during initialization.In the main loop, after setting CR2|=0X80, the send interrupt is immediately...
pcb168 stm32/stm8
Is there any project you can recommend?
Is there any project you can recommend? I am studying 2440 and hope to find a project to practice. I feel that some things I learn will be forgotten if I don't use them....
木凉凉 Embedded System
74LS160 digital circuit digital electronic clock circuit design
A digital electronic clock is a timing device that uses digital display of seconds, minutes, hours, and days. Compared with traditional mechanical clocks, it has the advantages of accurate timekeeping...
fish001 Analogue and Mixed Signal
Competition Information
[i=s] This post was last edited by paulhyde on 2014-9-15 09:45 [/i] Some practical examples of competitions, and various op amp chips...
ottomia1 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2922  207  2687  1513  253  59  5  55  31  6 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号