EEWORLDEEWORLDEEWORLD

Part Number

Search

LTC3602IFE-TRPBF

Description
2.5A, 10V, Monolithic Synchronous Step-Down Regulator
File Size222KB,20 Pages
ManufacturerLinear ( ADI )
Websitehttp://www.analog.com/cn/index.html
Download Datasheet Compare View All

LTC3602IFE-TRPBF Overview

2.5A, 10V, Monolithic Synchronous Step-Down Regulator

FEATURES
n
n
n
n
n
n
n
n
n
n
n
n
LTC3602
2.5A, 10V, Monolithic
Synchronous Step-Down
Regulator
DESCRIPTION
The LTC
®
3602 is a high efficiency, monolithic synchronous,
step-down DC/DC converter utilizing a constant-frequency,
current mode architecture. It operates from an input voltage
range of 4.5V to 10V and provides an adjustable regulated
output voltage from 0.6V to 9.5V while delivering up to
2.5A of output current. The internal synchronous power
switch with 65mΩ on-resistance increases efficiency
and eliminates the need for an external Schottky diode.
The switching frequency can either be set by an external
resistor or synchronized to an external clock. OPTI-LOOP
®
compensation allows the transient response to be optimized
over a wide range of loads and output capacitors.
The LTC3602 can be configured for either Burst Mode op-
eration or forced continuous operation. Forced continuous
operation reduces noise and RF interference, while Burst
Mode operation provides the high efficiency at light loads.
In Burst Mode operation, external control of the burst
clamp level allows the output voltage ripple to be adjusted
according to the requirements of the application.
, LT, LTC, LTM, Burst Mode and OPTI-LOOP are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Wide Input Voltage Range: 4.5V to 10V
2.5A Output Current
Low R
DS(ON)
Internal Switches: 65mΩ and 90mΩ
Programmable Frequency: 300kHz to 3MHz
Low Quiescent Current: 75μA
0.6V ±1% Reference Allows Low Output Voltage
99% Maximum Duty Cycle
Adjustable Burst Mode
®
Clamp
Synchronizable to External Clock
Power Good Output Voltage Monitor
Overtemperature Protection
Available in 16-Lead Exposed TSSOP and
4mm
×
4mm QFN Packages
APPLICATIONS
n
n
n
n
Point-of-Load Supplies
Portable Instruments
Server Backplane Power
Battery-Powered Devices
TYPICAL APPLICATION
3.3V, 2.5A, 1MHz Step-Down Regulator
V
IN
4.5V TO 10V
22μF
RUN
R
T
105k
2.2μH
PGOOD
TRACK/SS
4.32k
I
TH
1nF
SYNC/MODE
V
FB
PGND
475k
22pF
3602 TA01
Efficiency and Power Loss vs Load Current
100
95
V
IN
= 7V
EFFICIENCY
1000
POWER LOSS
80
75
70
65
60
0.01
0.1
1
LOAD CURRENT (A)
1
10
3602 TA01b
10000
PV
IN
INTV
CC
BOOST
0.22μF
1μF
EFFICIENCY (%)
90
85
POWER LOSS (mW)
100
LTC3602
SW
100μF
V
OUT
3.3V
2.5A
10
105k
3602fb
1

LTC3602IFE-TRPBF Related Products

LTC3602IFE-TRPBF LTC3602EFE-TRPBF LTC3602EUF-TRPBF LTC3602IUF-PBF LTC3602IUF-TRPBF
Description 2.5A, 10V, Monolithic Synchronous Step-Down Regulator 2.5A, 10V, Monolithic Synchronous Step-Down Regulator 2.5A, 10V, Monolithic Synchronous Step-Down Regulator 2.5A, 10V, Monolithic Synchronous Step-Down Regulator 2.5A, 10V, Monolithic Synchronous Step-Down Regulator
Is there a dual Schottky diode similar to BAT54x that can pass a larger current (0.6A*2)?
RT! As shown in the picture Requirements: Single tube current0.5A, dual tube1A; Forward conduction voltage0.4V; Reverse breakdown voltage20V...
oyhprince Analog electronics
Discussion on the Link between Test Equipment and Design Tools
Discussion on the Link between Test Equipment and Design Tools...
feifei Test/Measurement
Is there any good software architecture for microcontroller embedded projects?
MCU, stm32 good overall software architecture...
pengyongnet 51mcu
IAR downloader problem
I have a question: I have a TM4c123 development board, and a project developed with IAR. The program runs normally using the download and debug method, but if I download the program using download and...
sh820 Microcontroller MCU
Beaglebone peripheral circuit ee_fpga_cape debugging record (4) - Continue NAND
Poor U-boot 2011.09 didn't even know about the 4GB nandfalsh. Now I've focused on debugging and won't do any porting for the time being. I had no choice but to change to a 256MB nand and U-BOOT finall...
chenzhufly DSP and ARM Processors
I wrote a program for the lanchapad pocket experimental platform, but it kept giving me an error.
Error[e27]: Entry "TCA6416A_inputBuffer" in module TCA6416A ( G:\msp430\Pocket Experiment Platform led\Debug\Obj\TCA6416A.r43 ) redefined in module main ( G:\msp430\ What is going on? Baidu has not fo...
无酒亦醉 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2597  2835  571  581  2106  53  58  12  43  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号